Honeywell All in One Printer 3310G User Manual

Vuquest™ 3310g  
Area-Imaging Scanner  
Quick Start Guide  
Aller à www.honeywellaidc.com pour le français.  
Vai a www.honeywellaidc.com per l'italiano.  
Für Deutsch gehe zu www.honeywellaidc.com.  
Ir a www.honeywellaidc.com para español.  
Para Português, acesse www.honeywellaidc.com.br.  
Перейти на русскоязычный сайт www.honeywellaidc.com.  
查看繁体版请登陆 www.honeywellaidc.com  
한글 www.honeywellaidc.com 로 이동합니다 .  
Pro češtinu jdi na www.honeywellaidc.com.  
Pre slovenčinu choď na www.honeywellaidc.com  
3310-QS Rev C  
2/13  
 
Connecting the Scanner  
USB:  
Keyboard Wedge:  
 
RS232 Serial Port:  
Reading Techniques  
The view finder projects an aiming  
beam that should be centered over  
the bar code, but it can be  
positioned in any direction for a  
good read.  
Hold the scanner over the bar code,  
press the trigger, and center the  
aiming beam on the bar code.  
The aiming beam is smaller when  
the scanner is closer to the code and larger when it is farther from the  
code. Hold the scanner close to smaller bar codes, and farther away  
from large bar codes to get a proper read.  
If the bar code is highly reflective (e.g., laminated), you may need to  
tilt the scanner at an angle so the bar code can be scanned.  
 
Standard Product Defaults  
The following bar code resets all standard product default settings.  
Standard Product Defaults  
USB HID  
Scan the following code to program the scanner for USB HID bar  
code scanners.  
USB HID Bar Code Scanner  
USB Serial  
Scan the following code to program the scanner to emulate a regular  
RS232-based COM Port. If you are using a Microsoft® Windows®  
PC, you will need to download a driver from the Honeywell website  
(www.honeywellaidc.com). The driver will use the next available  
COM Port number. Apple® Macintosh computers recognize the  
scanner as a USB CDC class device and automatically uses a class  
driver.  
USB Serial  
 
Keyboard Country  
Scan the Program Keyboard Country bar code below, then scan  
the numeric bar code(s) from page 2, then the Save bar code to  
program the keyboard for your country. As a general rule, the  
following characters are not supported by the scanner for countries  
other than the United States:  
@ | $ # { } [ ] = / ‘ \ < > ~.  
Program Keyboard Country  
Country Code  
Belgium  
Scan Country Code  
Scan  
1
8
2
3
4
7
Italy  
5
Denmark  
Norway  
9
Finland  
Spain  
10  
6
France  
Switzerland  
USA (Default)  
Germany/Austria  
Great Britain  
0
Save  
Note: For a complete list of country codes, see the User’s Guide for  
 
Trigger  
The following bar codes will allow you to use the scanner in Manual  
Trigger - Normal Mode (need to press the trigger to read) or  
Presentation mode (the scanner is activated when it “sees” a bar  
code).  
Manual Trigger - Normal  
(Default)  
Presentation Mode  
Streaming Presentation  
When in Streaming Presentation mode, the scanner leaves the scan  
illumination on all the time and continuously searches for bar codes.  
Streaming Presentation Mode  
 
Mobile Phone Read Mode  
When this mode is selected, your scanner is optimized to read bar  
codes from mobile phone or other LED displays. You can enable  
Mobile Phone Reading for either a hand held device, or for a hands-  
free (presentation) application.  
Hand Held Scanning -  
Mobile Phone  
Streaming Presentation -  
Mobile Phone  
Suffix  
If you want a carriage return after the bar code, scan the Add CR  
Suffix bar code. To add a tab after the bar code, scan the Add Tab  
Suffix bar code. Otherwise, scan the Remove Suffix bar code to  
remove the suffixes.  
Add CR Suffix  
Add Tab Suffix  
Remove Suffix  
 
Add Code ID Prefix to all Symbologies  
Scan the following bar code if you wish to add a Code ID prefix to all  
symbologies at once.  
Add Code ID Prefix To All Symbologies  
(Temporary)  
Note: For a complete list of Code IDs, see the User’s Guide for your  
Function Code Transmit  
When this selection is enabled and function codes are contained  
within the scanned data, the scanner transmits the function code to  
the terminal. Charts of these function codes are provided in your  
User’s Guide. When the scanner is in keyboard wedge mode, the  
scan code is converted to a key code before it is transmitted.  
Enable  
(Default)  
Disable  
 
Data Format Editor Instructions  
The following are abbreviated instructions for entering a data format.  
For complete instructions refer to your User’s Guide, available at our  
1. Scan the Enter Data Format symbol.  
2. Primary/Alternate Format: scan 0 for Primary Format  
3. Terminal Type: scan 099 for any terminal type  
4. Code I.D.: scan 99 for any bar code type  
5. Length: scan 9999 for any length bar code.  
6. Editor commands: use the Programming Chart that follows.  
7. Scan Save to save your entries.  
Enter Data Format  
Clear All Data Formats  
Save  
 
Programming Chart  
0
1
2
4
3
5
7
6
 
 
8
9
B
D
F
A
C
E
Save  
 
EZConfig-Scanning  
To access additional features for the scanner use EZConfig-  
Scanning, an online configuration software tool, available from our  
 
Technical Assistance  
Contact information for technical support, product service, and repair  
can be found at www.honeywellaidc.com.  
Limited Warranty  
product’s warranty information.  
Patents  
For patent information, refer to www.honeywellaidc.com/patents.  
User Documentation  
For localized versions of this document, and to download the User’s  
Guide, go to www.honeywellaidc.com.  
Disclaimer  
Honeywell International Inc. (“HII”) reserves the right to make changes in  
specifications and other information contained in this document without prior  
notice, and the reader should in all cases consult HII to determine whether  
any such changes have been made. The information in this publication does  
not represent a commitment on the part of HII.  
HII shall not be liable for technical or editorial errors or omissions contained  
herein; nor for incidental or consequential damages resulting from the  
furnishing, performance, or use of this material.  
This document contains proprietary information that is protected by copyright.  
All rights are reserved. No part of this document may be photocopied,  
reproduced, or translated into another language without the prior written  
consent of HII.  
© 2012-2013 Honeywell International Inc. All rights reserved.  
Other product names or marks mentioned in this document may be  
trademarks or registered trademarks of other companies and are the property  
of their respective owners.  
 

Graco Heat Pump 311304J User Manual
Hamilton Beach Blender 70300 User Manual
Hamilton Beach Griddle 38546 User Manual
Hamilton Beach Rice Cooker 37532 User Manual
Hans Grohe Plumbing Product 28519XX1 User Manual
Hasbro Games Narnia User Manual
Hotpoint Freezer HZ1421 User Manual
HP Hewlett Packard Laptop 110 User Manual
Husky Paint Sprayer HDS550 User Manual
IKEA Microwave Oven IMH15 User Manual