Harman Speaker SAT 750 User Manual

INFP1419SAT-750 OM 9/8/03 4:01 PM Page 1  
TOTAL SPEAKER SOLUTIONS  
SAT-750  
Owner’s Guide  
 
INFP1419SAT-750 OM 8/11/03 10:37 AM Page 2  
 
INFP1419SAT-750 OM 8/11/03 10:37 AM Page 3  
SAT-750 OWNERS GUIDE  
Table of Contents  
2
2
2
3
3
4
4
4
Introduction  
Unpacking the Speaker  
Placement  
Wall-Mounting the Satellites  
Speaker Connections  
Operation  
Maintenance and Service  
Specifications  
1
SAT-750  
 
INFP1419SAT-750 OM 8/11/03 10:38 AM Page 4  
HomeTheater  
INTRODUCTION  
For front-channel use, place one speaker on the left and another  
on the right, along either side of the television monitor. Since the  
speakers are magnetically shielded, you can place them without  
worrying about the field distorting the TV picture.  
For surround-channel use, place speakers on bookshelves or  
stands alongside the listening position. Final placement depends  
on room acoustics, availability of space, and your listening  
preference (Figures 2 and 3).  
InfinityTotal Solutions  
Infinity Total Solutions continues Infinity’s longstanding  
commitment to accurate sound reproduction. Our proprietary  
Metal Matrix Diaphragm (MMD ) drivers, precision dividing  
networks and rigid, well-braced enclosures combine to deliver  
uncompromised performance in any stereo or multichannel home  
theater system. In addition, these speakers, except for the  
powered subwoofer, are magnetically shielded for safe  
placement adjacent to a television.  
In 6 or 7 channel configurations, place the rear channel(s)  
behind the listening position, as shown in Figures 2 and 3.  
NOTE: An Infinity powered subwoofer will add impact and realism  
to both music and film soundtracks. Contact your Infinity dealer  
for recommendations on subwoofer models for your application.  
Unpacking the Speaker  
If you suspect damage from transit, report it immediately to your  
dealer. Keep the shipping carton and packing materials for  
future use.  
Infinity Subwoofer  
(optional)  
Left  
Front  
Channel  
Right  
Front  
Channel  
PLACEMENT  
Center  
Channel  
Stereo  
Before deciding where to place your speakers, survey your room  
and think about placement, keeping the following points in mind,  
using Figure 1 as a guide:  
For best results, place the speakers 6'– 8' apart.  
Couch  
Position each speaker so that the tweeter is approximately  
at ear level.  
Left  
Surround  
Channel  
Right  
Surround  
Channel  
Generally, bass output will increase as the speaker is  
moved closer to a wall or corner.  
Left Rear  
Channel  
Center Rear  
Channel  
Right Rear  
Channel  
Refer to“Home Theaterbelow if you also plan to use  
the speakers for home theater reproduction.  
Figure 2.This overhead view shows a typical home theater plan.  
Left/right rear channels are for a 7-channel system. Center rear  
channel is for a 6-channel system.  
Left  
Right  
(optional)  
Channel  
Channel  
Listening Position  
Right Rear  
Channel  
Figure 1.This overhead view shows typical positioning  
in stereo applications.  
Center Rear  
Channel  
Left Rear  
Channel  
Figure 3.This figure shows an alternate layout, which may be  
more suitable for some rooms. Left/right rear channels are for a  
7-channel system. Center rear channel is for a 6-channel system.  
2
SAT-750  
 
INFP1419SAT-750 OM 8/11/03 10:38 AM Page 5  
WALL-MOUNTING THE SATELLITES  
S
PEAKER CONNECTIONS  
The SAT-750 satellites are designed to be mounted on the wall.  
There is a wall bracket for each satellite speaker. Each speaker  
bracket will require (2) 1-1/2," # 10 wood screws; each screw  
should be fastened to a wall stud. If a wall stud is unavailable,  
install an anchor appropriate for a 1-1/2," # 10 screw.  
Turn Off All Power  
First, turn off all audio-system power. Use high-quality speaker  
wire to make your connections. # 18-Gauge speaker wire with  
polarity coding is recommended. For longer distances, # 16-gauge  
or heavier wire is recommended.The side of the wire with a ridge  
or other coding is usually considered positive polarity (i.e., +).  
Also, consult the owners manuals that were included with your  
amplifier or receiver to confirm connection procedures.  
Observe polarities when making speaker connections, as shown  
in Figure 5. Connect each + terminal on the back of the  
amplifier or receiver to the respective + (red) terminal on each  
speaker. Connect the – (black) terminals in the same way.  
NOTE: The customer is responsible for the correct selection  
and use of mounting hardware (available through hardware  
stores) that will ensure the proper and safe wall-mounting of  
the speakers.  
Step 1.  
Mark the positions on the wall where you would like to place the  
mounting screws.  
Important!  
Step 2.  
Do not reverse polarities (i.e., + to – or – to +) when making  
connections. Doing so will cause poor imaging and diminished  
bass response. Be certain that positive and negative wire strands  
are completely isolated to avoid short circuits that may damage  
your equipment.  
Place bracket against wall and fasten two 1-1/2," # 10 wood  
screws through the brackets screw holes into the wall. If a wall  
stud is not available, use an appropriate anchor.  
Step 3.  
Place the speaker on the wall by sliding the opening on the  
bottom of the speaker over the bracket hook on the wall. Once  
positioned properly, the speaker should slide down slightly and  
become secure.  
keyhole on the back of the speaker to the screwhead on the wall.  
Once positioned properly, the speaker should  
slide down slightly and become secure.  
Figure 4.  
®
+
Bracket on wall.  
Figure 5. Wiring diagram shows polarity connections  
for one channel of a home theater system.  
3
SAT-750  
 
INFP1419SAT-750 OM 8/11/03 10:38 AM Page 6  
OPERATION  
SPECIFICATIONS  
Surround Modes  
When using the system in a Dolby* Digital or DTS home theater  
system, make sure all SAT-750 speakers are set to“Small.  
SAT-750  
Frequency Range:  
120Hz – 20,000Hz (±3dB)  
When using the SAT-750 in a Dolby Pro Logic* home theater  
system, make sure the receivers center channel mode is set  
to“Normal.”  
Recommended  
Amplifier Power Range:  
10 – 100 watts  
88dB  
Some Dolby Digital-equipped receivers/processors offer different  
setup options for each source or surround mode, e.g., CD-stereo,  
videotape, Dolby, Pro Logic. In each case, follow your equipments  
instructions to ensure that the subwoofer output is turned on and  
that the speakers are set to“Smallin each mode.  
Sensitivity:  
(2.83V @ 1 meter)  
Nominal Impedance:  
Crossover Frequency:  
Midrange Driver(s):  
8  
3500Hz, 24dB/octave  
MAINTENANCE AND SERVICE  
3-1/2" MMD,  
magnetically shielded  
The satellite enclosure may be cleaned using a soft cloth to  
remove fingerprints or to wipe off dust.  
High-Frequency Driver:  
Dimensions (H x W x D):  
Weight:  
3/4" MMD,  
All wiring connections should be inspected and cleaned or  
remade periodically.The frequency of maintenance depends on  
the metals involved in the connections, atmospheric conditions,  
and other factors, but once per year is the minimum.  
magnetically shielded  
6" x 4-1/8" x 4-3/8"  
(152mm x 105mm x 111mm)  
If a problem occurs, make sure that all connections are properly  
made and clean. If a problem exists in one loudspeaker, reverse  
the connection wires to the left and right system. If the problem  
remains in the same speaker, then the fault is with the loud-  
speaker. If the problem appears in the opposite speaker, the  
cause is in another component or cable. In the event that  
your SAT-750 ever needs service, contact your local Infinity  
dealer or Infinity directly at 516-674-4INF (USA only) or  
www.infinitysystems.com for a service center near you.  
2.8 lb (1.3kg)  
Infinity continually strives to update and improve existing products, as well as  
create new ones.The specifications and construction details in this and  
related Infinity publications are therefore subject to change without notice.  
4
SAT-750  
 
INFP1419SAT-750 OM 8/11/03 10:38 AM Page 7  
NOTES  
 
INFP1419SAT-750 OM 8/11/03 10:37 AM Page 8  
© 2003 Harman International Industries, Incorporated  
Infinity Systems, 250 Crossways Park Drive,Woodbury, NY 11797 USA 516.674.4INF (USA only) www.infinitysystems.com  
*Trademarks of Dolby Laboratories. DTS is a registered trademark of Digital Theater Systems, Inc. Infinity is a registered trademark, and Total Solutions and MMD are a trademarks, of Harman International Industries, Incorporated.  
 

Graco Baby Accessories ISPH015AC User Manual
Graco Inc Paint Sprayer 218688 User Manual
Hamilton Beach Oven 22703 User Manual
Harbor Freight Tools Planer 10 Auto Planer User Manual
Harmar Mobility Mobility Aid AL003 User Manual
Heath Zenith Work Light 52 4473 6 User Manual
Hotpoint Washer WML 940 User Manual
iHome Cell Phone IB967 User Manual
Ikelite Carrying Case DCR SR190 User Manual
Image Home Gym 831159701 User Manual