Harman Kardon Stereo Receiver AVR 700 User Manual
AVR 700/AVR 70/AVR 70C  
Audio/video receiver  
Owner’s Manual  
 
Introduction, Supplied Accessories,  
AVR 700/AVR 70/AVR 70C Important Safety Information and Place the AVR  
Introduction  
IMPORTANT SAFETY INFORMATION  
Thank you for choosing this Harman Kardon product!  
Verify Line Voltage Before Use  
formorethanfiftyyears, theharmankardonmissionhasbeentoshareapassionformusic  
and entertainment, using leading-edge technology to achieve premium performance.  
Sidney harman and bernard kardon invented the receiver, a single component designed  
to simplify home entertainment without compromising performance. over the years,  
harman kardon products have become easier to use while offering more features and  
sounding better than ever.  
the AVr 700 has been designed for use with 120-volt alternating current (Ac). the  
AVr 70 and AVr 70c have been designed for use with 220 – 240-volt Ac. connection  
to a line voltage other than that for which your AVr is intended can create a safety  
and fire hazard, and may damage the unit. If you have any questions about the voltage  
requirements for your specific model or about the line voltage in your area, contact your  
selling dealer before plugging the unit into a wall outlet.  
the AVr 70, AVr 700 and AVr 70c 5.1-channel digital audio/video receivers (AVrs)  
continue this tradition with some of the most advanced audio and video processing  
capabilities yet and a wealth of listening and viewing options.  
Do Not Use Extension Cords  
to avoid safety hazards, use only the power cord supplied with your unit. we do not  
recommend that extension cords be used with this product. As with all electrical devices,  
do not run power cords under rugs or carpets, or place heavy objects on them. damaged  
power cords should be replaced immediately by an authorized service center with a cord  
meeting factory specifications.  
to obtain the maximum enjoyment from your new AVr, please read this manual and refer  
back to it as you become more familiar with its features and their operation.  
If you have any questions about this product, its installation or its operation, please  
contact your harman kardon retailer or custom installer, or visit our web site at www.  
harmankardon.com.  
Handle the AC Power Cord Gently  
when disconnecting the power cord from an Ac outlet, always pull the plug; never  
pull the cord. If you do not intend to use your AVr for any considerable length of time,  
disconnect the plug from the Ac outlet.  
Supplied Accessories  
the following accessory items are supplied with your AVr. If any of these items are  
missing, please contact your harman kardon dealer, or harman kardon customer service  
at www.harmankardon.com.  
Do Not Open the Cabinet  
there are no user-serviceable components inside this product. opening the cabinet may  
present a shock hazard, and any modification to the product will void your warranty. If  
water or any metal object such as a paper clip, wire or staple accidentally falls inside  
the unit, disconnect it from the Ac power source immediately, and consult an authorized  
service center.  
• IR remote control  
• AM loop antenna  
• FM wire antenna  
• Three AAA batteries  
• AC power cord  
CATV or Antenna Grounding (AVR 700)  
If an outside antenna or cable system is connected to this product, be certain that it is  
grounded so as to provide some protection against voltage surges and static charges.  
Section 810 of the united States national electrical code, AnSI/nfpA no. 70-1984,  
provides information with respect to proper grounding of the mast and supporting  
structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding  
conductors, location of antenna discharge unit, connection to grounding electrodes and  
requirements of the grounding electrode.  
NOTE TO CATV SYSTEM INSTALLER: this reminder is provided to call the cAtV (cable  
tV) system installer’s attention to article 820-40 of the nec, which provides guidelines  
for proper grounding and, in particular, specifies that the cable ground shall be connected  
to the grounding system of the building, as close to the point of cable entry as possible.  
Place the AVR  
• Place the AVR on a firm and level surface. Be certain that the surface and any  
mounting hardware can support the AVr’s weight.  
• Provide proper space above and below the AVR for ventilation. Recommended  
clearance distances are 30cm above the unit, 10cm behind the unit and 20cm on  
each side of the unit.  
• If you install the AVR in a cabinet or other enclosed area, provide cooling air within the  
cabinet. under some circumstances, a fan may be required.  
• Do not obstruct the ventilation slots on the top of the AVR or place objects directly  
over them.  
• Do not place the AVR directly on a carpeted surface.  
• Do not place the AVR in moist or humid locations, in extremely hot or cold locations,  
in areas near heaters or heat registers, or in direct sunlight.  
3
 
AVR 700/AVR 70/AVR 70C  
Front-Panel Controls  
Front-Panel Controls  
Standby  
Indicator  
Ir  
Sensor  
message  
display  
memory/folder  
button  
Volume  
control  
power on Indicator  
(inside Volume control ring)  
main power  
Switch  
on/Standby  
Switch  
Surround mode  
Select buttons  
Am/fm  
button  
Source Select  
buttons  
uSb  
port  
Video 3  
Audio and Video  
Input connectors  
Stereo mode  
button  
tuning up/down  
button  
preset Selector  
buttons  
headphone  
connector  
Main Power switch: this mechanical switch turns the AVr’s power supply on or off. It is  
usually left on and cannot be turned on or off using the remote control.  
IMPORTANT NOTE: If the protect message ever appears on the message display,  
turn off the AVr and unplug it from the Ac outlet. check all speaker wires for a  
possible short circuit (the “+” and “–” conductors touching each other or both  
touching the same piece of metal). If a short circuit is not found, bring the unit to  
an authorized harman kardon service center for inspection and repair before using  
it again.  
Standby indicator: this led glows amber to indicate that the AVr is in the Standby  
mode.  
Power On/Standby button: press this button to turn the AVr on and put it into the  
Standby mode. when the AVr is on the power on indicator glows blue and the Standby  
indicator turns off.  
Stereo Mode button: places the AVr in the stereo listening mode.  
Preset Selector buttons: when the radio is in use, press these buttons to cycle through  
your preset radio stations.(See Listening to FM and AM Radio, on page 16, for more  
information.) note: when you're listening to files on a uSb device, the tuning up/down  
buttons and the preset Selector buttons serve as the uSb device’s transport control  
buttons.(See Playing Files on a USB Device, on page 16, for more information.)  
IR Sensor: this sensor receives infrared (Ir) commands from the remote control. It is  
important to ensure that the sensor is not blocked.  
Surround Mode Select buttons: press these buttons to select a surround listening  
mode. Surround-mode availability depends on the nature of the source input signal, i.e.,  
digital versus analog, and the number of channels encoded within the signal.  
Source Select buttons: press these buttons to select the active source device.  
Memory/Folder button: when the radio is in use, press this button to set the current  
station as a preset. See Listening to FM and AM Radio, on page 16, for more information.  
when a uSb device is the active source deivce, press this button to display the contents  
of the current folder or to display all of the folders in the current directory level. See  
Playing files on a USB Device, on page 16, for more information.  
Tuning Up/Down buttons: use these buttons to tune radio stations according to the  
setting of the Am/fm button (see below).  
AM/FM button: press this button to listen to the radio. pressing this button when the  
radio is in use will select among the fm Stereo, fm mono and Am bands. See Listening  
to FM and AM Radio, on page 16, for more information.  
Headphone connector: connect a 1/4" stereo headphone plug to this jack for private  
listening  
Message display: Various messages appear in this display in response to commands  
and changes in the incoming signal. In normal operation, the current source device name,  
surround mode and active input appear. when the on-screen display menu system (oSd)  
is in use, the current menu settings appear.  
USB Port: Insert a flash drive or hdd disk drive with a uSb Standard-A cable to this port.  
Volume control: turn this knob to raise or lower the volume.  
Video 3 Audio and Video Input connectors: connect an auxiliary audio/video source  
component that will be used only temporarily, such as a camcorder, portable music  
player or game console, here.  
4
 
AVR 700/AVR 70/AVR 70C  
Rear-Panel Connectors  
Rear-Panel Connectors  
digital Audio  
connectors  
hdmI®  
connectors  
composite Video  
connectors  
Ac Input  
connector  
radio Antenna  
connectors  
Analog Audio  
connectors  
Subwoofer  
connector  
Speaker  
connectors  
Radio Antenna connectors: connect the included Am and fm antennas to their  
respective terminals for radio reception. See Connect the Radio Antennas, on page 13,  
for more information.  
Subwoofer connector: connect this jack to a powered subwoofer that has a line-level  
input connector. See Connect Your Subwoofer, on page 11, for more information.  
Composite Video connectors: use composite video connectors for video source devices  
and a tV that don’t have hdmI connectors. you will also need to make audio connections  
from the source devices to the AVr. See Connect Your Source Devices, on page 11, for  
more information.  
Digital Audio connectors: If your non-hdmI source devices have digital outputs,  
connect them to the AVr’s digital audio connectors. See Connect Your Source Devices,  
on page 11, for more information.  
Analog Audio connectors: use the AVr’s Analog Audio connectors for source devices  
that don’t have hdmI or digital audio connectors. use the Video 1 out, Video 2 out and  
tape out connectors to connect to the audio inputs of Vcrs, tape decks or other analog  
recorders. See Connect Your Source Devices, on page 11, for more information.  
IMPORTANT: the AVr’s on-screen display (oSd) only appears through the composite  
monitor out connector. If you want to use the AVr’s oSd menus you need to connect  
its composite monitor out connector to your tV even if you are not connecting any  
composite video source devices to the AVr.  
HDMI connectors: the hdmI (high-definition multimedia Interface®) feature is a  
connection for transmitting digital audio and video signals between devices. If your  
source devices and tV have hdmI connectors, using them will provide the best possible  
video and audio performance quality. Since the hdmI cable carries both digital video  
and digital audio signals, you do not have to make any additional audio connections for  
devices you connect via hdmI connections. See Connect Your Source Devices, on page  
11, for more information.  
Speaker connectors: use two-conductor speaker wire to connect each set of terminals  
to the correct speaker. See Connect Your Speakers, on page 11, for more information.  
AC Input connector: After you have made all other connections, plug the supplied Ac  
power cord into this receptacle and into an unswitched wall outlet.  
Notes on using the HDMI Out connector:  
• When connecting a DVI-equipped display to the HDMI Monitor Out connector, use  
an hdmI-to-dVI adapter and make a separate audio connection.  
• Make sure the HDMI-equipped display is HDCP-compliant. If it isn’t, do not connect  
it via hdmI; use an analog video connection instead and make a separate audio  
connection.  
5
 
AVR 700/AVR 70/AVR 70C  
System Remote Control Functions  
Remote Control Functions  
Ir transmitter lens  
mute button  
power on button  
AVr button  
power off button  
Source Selector buttons  
tone controls button  
Stereo mode button  
Surround mode Select buttons  
display mode button  
Volume up/down buttons  
test tone Sequence button  
Setup menu button  
Audio Input Select button  
ok button  
back/exit button  
channel level button  
left/right/up/down buttons  
number buttons  
memory button  
tuning up/down buttons  
Sleep/clear button  
preset Station up/down buttons  
display dim button  
repeat/random button  
track Skip up/down buttons  
transport control buttons  
6
 
AVR 700/AVR 70/AVR 70C  
System Remote Control Functions, continued  
Audio Input Select button: press this button to select the specific digital audio input (or  
analog audio input) to which the current source is connected. each press of the button  
advances through the following inputs: optical digital 1, optical digital 2, coaxial digital,  
hdmI (for hdmI 1 – hdmI 3 only) and Analog. this button does not function for the Am/  
fm and uSb sources.  
Remote Control Functions, continued  
In addition to controlling the AVr, the AVr remote can also control a harman kardon blu-  
ray disc® or dVd player that is connected to the hdmI 1 connector. the remote control  
buttons will have different functions depending on if the remote is controlling the AVr or  
a blu-ray disc or dVd player. Appendix A5, Remote Control Function List, on page 25,  
provides a list of the different remote control button functions when controlling a blu-ray  
disc or dVd player.  
Setup Menu button: press this button to activate the setup menus. See Set Up the AVR,  
on page 14, for more information.  
OK button: this button is used to select items from the menu system.  
IR Transmitter lens: As buttons are pressed on the remote, infrared codes are emitted  
through this lens.  
Back button: when you’re using the setup menus, press this button to return to the  
previous menu screen.  
Power On/Off buttons: press these buttons to turn the AVr on and off. the main power  
switch on the AVr’s front panel must be on for these buttons to turn the AVr on and off.  
Channel Level button: press this button to activate the individual channel-level  
adjustment. It lets you easily change the channel balance while you’re listening to suit  
different programs or seating arrangements. See Set Up the AVR, on page 14, for more  
information.  
Mute button: press this button to mute the AVr’s speaker-output connectors and  
headphone jack. to restore the sound, press this button or adjust the volume.  
AVR button: press this button to switch the remote’s control mode to operate the AVr.  
pressing this button when the AVr is in the Standby mode will turn it on.  
Left/Right/Up/Down buttons: these buttons are used to navigate the menu system.  
Number buttons: use these buttons to enter numbers for radio-station frequencies or  
to select station presets.  
Source Selector buttons: press one of these buttons to select a source device. this  
action will also turn on the AVr and switch the AVr to the selected input.  
Memory button: to save the currently tuned radio station as a preset, press this button,  
then a number button.  
• Pressing the TV Source Selector button plays the sound from the HDMI Audio Return  
channel, so you can listen to sources connected directly to the tV or to the tV itself  
through the AVr. See Additional Setup Menu Items: HDMI Set, on page 15, for more  
information.  
Tuning Up/Down buttons: press these buttons to tune a radio station. when you’re  
listening to an fm station, each press will either change one tuning frequency increment  
at a time or seek the next higher or lower station with acceptable signal strength,  
depending on whether you are listening in fm mono or fm stereo.  
• The first press of the Radio Source Selector button switches the AVR to the last-used  
tuner band (Am or fm). Successive presses cycle through Am, fm stereo and fm  
mono.  
Preset Station Up/Down buttons: press these buttons to cycle through your preset  
radio stations.  
Stereo Mode button: press this button to switch to the stereo listening mode.  
Sleep/Clear button: press this button to activate the Sleep timer function. See Sleep  
Timer, on page 18, for more information. when controlling a harman/kardon blu-ray disc  
or dVd player, press this button to clear an entry.  
Tone Controls button: press this button to activate or bypass the bass and treble  
controls. when the tone controls are set to “on”, use the up, down, left and right arrow  
buttons to vary the tone quality by adjusting the bass and treble.  
Display Dimmer button: press this button to dim the AVr’s front-panel display partially  
or fully.  
Surround Mode Select buttons: press these buttons to select a surround listening  
mode. Surround-mode availability depends on the nature of the source input signal,  
i.e., digital versus analog, and the number of channels encoded within the signal. See  
Selecting a Surround Mode and Audio Processing and Surround Sound, on page 17, for  
more information.  
Repeat/Random button: this button has no effect on the AVr but can be used to  
activate the repeat function when you’re listening to media on a device inserted into the  
AVr’s uSb port and the repeat and random functions on a harman kardon blu-ray disc or  
dVd player. See Listening to Media on a USB Device, on page 16, for more information.  
Volume Up/Down buttons: press these buttons to raise or lower the volume.  
Track Skip Up/Down buttons: these buttons have no effect on the AVr but are used to  
change tracks or chapters when you’re listening to media on a device inserted into the  
AVr’s uSb port, or on a harman kardon blu-ray disc or dVd player.  
Display Mode button: press this button to display the active surround mode and current  
volume control setting on the AVr’s message display. After five seconds the display will  
revert back to showing the currently-active source.  
Transport Control buttons: these buttons have no effect on the AVr but are used to  
control a harman kardon blu-ray disc player or dVd player or a device inserted in the  
AVr’s uSb port.  
Test Tone sequence button: press this button to activate the test tone for calibrating  
channel volume levels by ear.  
7
 
Introduction to Home Theater  
and Place Your Speakers  
AVR 700/AVR 70/AVR 70C  
Introduction to Home Theater  
Place Your Speakers  
this introductory section will help you to familiarize yourself with some basic concepts  
unique to multichannel surround-sound AVrs, which will make it easier for you to set up  
and operate your AVr.  
determine the locations for your system’s speakers according to their manufacturer’s  
directions and the layout of your listening room. use the illustration below as a guide for  
5.1-channel systems.  
to create the most realistic surround-sound environment possible, you should place  
your speakers in a circle with the listening position at its center. you should angle each  
speaker so it directly faces the listening position. use the diagram below as a guide.  
Typical Home Theater System  
A home theater typically includes an audio/video receiver (AVr), which controls the system  
and supplies amplification for the loudspeakers; a disc player; a source component for  
television broadcasts (cable box, satellite dish AVr, hdtV tuner or antenna connected to  
the tV); a tV or video display; and multiple loudspeakers.  
tV  
Sub  
fr  
c
fl  
Multichannel Audio  
the main benefit of a home theater system is its ability to produce “surround sound.”  
Surround sound uses multiple speakers and amplifier channels to immerse you in the  
audio/video presentation for a dramatically increased sense of realism.  
your AVr can have up to five main speakers connected directly to it, plus a subwoofer.  
each main speaker is powered by its own amplifier channel inside the AVr. A system  
with more than two speakers is called a multichannel system. the different main speaker  
types in a home theater system are:  
Sl  
Sr  
• Front Left and Right: the front left and right speakers are used as in a 2-channel  
system. In many surround-sound modes, these speakers are secondary, while the  
main action, especially dialogue, is reproduced by the center speaker.  
• Center: when you are watching movies and television programs, the center speaker  
reproduces most of the dialogue and other soundtrack information that occurs on the  
screen, anchoring it with the picture. when you are listening to a musical program,  
the center speaker helps to create a seamless front soundstage, creating a more  
realistic “you-are-there” listening experience.  
Placing the Left, Center and Right Speakers  
place the center speaker either on top of, below or mounted on the wall above or below  
the tV or video-display screen. place the front left and right speakers along the circle,  
about 30 degrees from the center speaker and angled toward the listener.  
• Surround Left and Right: the surround left and right speakers produce ambient  
sounds that help create a realistic and immersive surround-sound environment. they  
also help recreate directional sound effects such as aircraft flyovers.  
place the front left, front right and center speakers at the same height, preferably at  
about the same height as the listener’s ears. the center speaker should be no more than  
2 feet (0.6m) above or below the left/right speakers. If you’re using only two speakers  
with your AVr, place them in the front left and front right positions.  
many people expect the surround speakers to play as loudly as the front speakers.  
Although you will calibrate all of the speakers in your system to sound equally loud  
at the listening position, most artists use the surround speakers for ambient effects  
only, and they create their programs to steer relatively little sound to these speakers.  
Placing the Surround Speakers  
• Subwoofer: A subwoofer is designed to play only the lowest frequencies (the deep  
bass). It augments smaller, limited-range main speakers that are usually used for  
the other channels. many digital-format programs, such as movies recorded in dolby  
digital, contain a low-frequency effects (lfe) channel that is directed to the subwoofer.  
the lfe channel packs the punch of a rumbling train or airplane, or the power of an  
explosion, adding realism and excitement to your home theater. Some people use two  
subwoofers for additional power and for even distribution of the sound.  
you should place the left and right surround speakers approximately 110 degrees from  
the center speaker, slightly behind and angled toward the listener. Alternatively, you can  
place them behind the listener, with each surround speaker facing the opposite-side  
front speaker. you should place the surround speakers 2 feet – 6 feet (0.6m – 1.8m)  
higher than the listener’s ears.  
NOTE: Your AVR will sound its best when the same model or brand of  
loudspeaker is used for all positions.  
Surround Modes  
there are different theories as to the best way to present surround sound and to distribute  
the individual channel information to the surround-sound system’s speakers. A variety  
of algorithms have been developed in an effort to recreate the way we hear sounds in  
the real world, resulting in a rich variety of options. Several companies have developed  
different surround-sound technologies, all of which can be accurately reproduced by  
your AVr:  
Placing the Subwoofer  
because a room’s shape and volume can have a dramatic effect on a subwoofer’s  
performance, it is best to experiment with placement so that you will find the location  
that produces the best results in your particular listening room. with that in mind, these  
rules will help you get started:  
• Dolby Laboratories: dolby truehd, dolby digital plus, dolby digital, dolby pro logic II,  
dolby pro logic.  
• Placing the subwoofer next to a wall generally will increase the amount of bass in  
the room.  
• DTS: dtS-hd™ high resolution Audio, dtS-hd master Audio™, dtS, dtS 96/24™,  
dtS neo: 6.  
• Placing the subwoofer in a corner generally will maximize the amount of bass in the  
room.  
• HARMAN International: Analog Surround modes (theater hall, Stadium, club,  
Arena).  
• In many rooms, placing the subwoofer along the same plane as the left and right  
speakers can produce the best integration between the sound of the subwoofer and  
that of the left and right speakers.  
• Stereo Modes: 2-channel stereo and 5-channel stereo.  
Appendix table A4, on page 22, contains detailed explanations of the different surround-  
sound options available on your AVr. digital surround-sound modes, such as dolby  
digital and dtS systems, are available only with specially encoded programs, such  
as those available via hdtV, dVd and blu-ray disc media and digital cable or satellite  
television. other surround modes may be used with digital and analog signals to create a  
different surround presentation or to use a different number of speakers. Surround-mode  
selection depends upon the number of speakers in your system, the programs you are  
watching or listening to, and your personal tastes.  
• In some rooms, the best performance could even result from placing the subwoofer  
behind the listening position.  
A good way to determine the best location for the subwoofer is by temporarily placing it in  
the listening position and playing music with strong bass content. move around to various  
locations in the room while the system is playing (putting your ears where the subwoofer  
would be placed), and listen until you find the location where the bass performance is  
best. place the subwoofer in that location.  
8
 
Types of Home Theater  
System Connections  
AVR 700/AVR 70/AVR 70C  
Subwoofer Connections  
Types of Home Theater System Connections  
the subwoofer is a speaker dedicated to reproducing only the low (bass) frequencies,  
which require more power. to obtain the best results, most speaker manufacturers offer  
powered subwoofers that contain their own amplifiers. use a single rcA audio cable  
(not included) to make a line-level (non-amplified) connection from the AVr’s Subwoofer  
connector to a corresponding input jack on the subwoofer.  
there are different types of audio and video connections used to connect the AVr to your  
speakers, your tV or video display, and your source devices. the consumer electronics  
Association has established the ceA® color-coding standard.  
Connection Color Guide Table  
Analog Audio Connection  
front left/right  
Color  
white/red  
green  
center  
Surround left/right  
Subwoofer  
blue/gray  
purple  
Color  
Although the AVr’s purple subwoofer output looks similar to a full-range analog audio  
jack, it is filtered so that only the low frequencies pass through it. don’t connect this  
output to any device other than a subwoofer.  
Digital Audio Connection  
coaxial (input or output)  
optical Input  
Source Device Connections  
orange  
black  
Audio and video signals originate in source devices (components where a playback  
signal originates) such as your blu-ray disc or dVd player, cd player, dVr (digital video  
recorder) or other recorder, tape deck, game console, cable or satellite television tuner,  
mp3 player or a device docked in the AVr’s uSb port. the AVr’s fm/Am tuner also counts  
as a source, even though no external connectors are needed other than the AVr’s fm and  
Am antennas. Separate connectors are required for the audio and video portions of the  
source device’s signal, except for digital hdmI connectors. the types of connectors you  
use will depend upon the capabilities of the source device and of your tV or video display.  
Analog Video Connection  
composite Video  
Color  
yellow  
Speaker Connections  
Speaker cables carry an amplified signal from the AVr’s speaker terminals to each  
loudspeaker. each cable contains two wire conductors, or leads, that are differentiated  
in some way, such as with colors or stripes.  
Digital Audio Connections – HDMI  
there are two types of audio connections – digital and analog. digital audio signals are  
required for listening to sources encoded with digital surround modes, such as dolby  
digital and dtS, or for uncompressed pcm digital audio. your AVr has three types of  
digital audio connectors: hdmI, coaxial and optical. do not use more than one type of  
digital audio connector for each source device. however, it’s okay to make both analog  
and digital audio connections to the same source.  
the differentiation helps you maintain proper polarity, without which your system’s low-  
frequency performance can suffer. each speaker is connected to the AVr’s speaker-  
output terminals using two wires, one positive (+) and one negative (–). Always connect  
the positive terminal on the speaker, which is usually colored red, to the positive terminal  
on the AVr, which is colored as indicated in the connection color guide table, above.  
the negative terminals on the speakers and the AVr are black.  
your AVr is equipped with four rear-panel hdmI input connectors and one hdmI monitor  
output connector. hdmI technology enables digital audio and video information to be  
carried using a single cable, delivering the highest quality picture and sound. If your tV  
or video-display device has an hdmI input connector, make a single hdmI connection  
from each source device to the AVr. usually, a separate digital audio connection is not  
required.  
your AVr uses binding-post speaker terminals that can accept bare-wire cables or  
banana plugs. bare-wire cables are installed as shown below:  
the AVr’s hdmI monitor output connector contains an Audio return channel (Arc) that  
carries a digital audio signal from your tV or video display back to the AVr. It allows  
you to listen to hdmI devices that are connected directly to your tV (such as an Internet  
connection) without making an additional connection from the device to the AVr. the  
Arc signal is active when the tV source is selected. See Additional Setup Menu Items,  
on page 15, for more information.  
1. unscrew cap  
2. Insert bare wire  
3. tighten cap  
the hdmI connector is shaped for easy plug-in (see illustration, below), and hdmI  
cable runs are limited to about 10 feet (3m). If your video display has a dVI input and is  
hdcp-compliant, use an hdmI-to-dVI adapter (not included), and make a separate audio  
connection.  
banana plugs are inserted into the hole in the middle of the terminal cap, as shown  
below:  
A. tighten cap  
b. Insert banana connector  
into hole in cap  
Always connect the colored (+) terminal on the AVr to the (+) terminal on the speaker  
(usually red), and the black (–) terminal on the AVr to the (–) terminal on the speaker  
(usually black).  
Digital Audio Connections – Coaxial  
coaxial digital audio jacks are usually color-coded orange. Although they look like  
standard rcA-type analog jacks, you should not connect coaxial digital audio outputs to  
analog inputs or vice versa.  
IMPORTANT: Make sure the ( + ) and ( – ) bare wires do not touch each other or  
the other terminal. Touching wires can cause a short circuit that can damage your  
AVR or amplifier.  
9
 
Types of Home Theater System  
Connections, continued  
AVR 700/AVR 70/AVR 70C  
Digital Audio Connections – Optical  
Radio Connections  
optical digital audio connectors are normally covered by a shutter to protect them from  
dust. the shutter opens as the cable is inserted. optical input connectors are color-coded  
using a black shutter.  
your AVr uses separate terminals for the included fm and Am antennas. the fm antenna  
uses a 75-ohm f-connector.  
the Am antenna connector uses spring-clip terminals. After assembling the antenna  
as shown below, press the levers to open the connectors, insert the bare wires into the  
openings, and release the levers to secure the wires.  
Analog Audio Connections  
two-channel analog connections require a stereo audio cable, with one connector for  
the left channel (white) and one for the right channel (red). these two connectors are  
attached to each other.  
USB Port  
the AVr can play mp3 and wmA audio files from a uSb device inserted into the uSb port.  
Insert the device into the uSb port oriented so it fits all the way into the port. you may  
insert or remove the device at any time – there is no installation or ejection procedure.  
for source devices that have both digital and analog audio outputs, you may make both  
connections.  
the analog connections also feed the Analog record output connectors. you may record  
materials from blu-ray disc recordings, dVds or other copy-protected sources using only  
analog connections. remember to comply with all copyright laws if you choose to make  
a copy for your own personal use.  
Video Connections  
many source devices output both audio and video signals (e.g., blu-ray disc, dVd  
player, cable television box, hdtV tuner, satellite box, Vcr, dVr). In addition to an audio  
connection as described above, make a video connection for each of these source  
devices. make only one type of video connection for each device.  
IMPORTANT: Do not connect a PC or other USB host/controller to the AVR’s USB  
port, or you may damage both the AVR and the other device.  
Digital Video Connections  
If you have already connected a source device to one of the AVr’s hdmI input connectors,  
you have automatically made a video connection for that device, since the hdmI cable  
carries both digital audio and digital video signals.  
Analog Video Connections – Composite Video  
composite video is the basic connection most commonly available. both the chrominance  
(color) and the luminance (intensity) components of the video signal are transmitted  
using a single cable. the jack is usually color-coded yellow and looks like an analog  
audio jack. do not connect a composite video jack to an analog audio or coaxial digital  
audio jack, or vice versa.  
10  
 
AVR 700/AVR 70/AVR 70C  
Making Connections  
Connect Your TV or Video Display  
HDMI Monitor Out connector  
Making Connections  
If your tV has an hdmI connector and you have hdmI or component video source  
devices, use an hdmI cable (not included) to connect your tV to the AVr’s hdmI monitor  
out connector. It will provide the best possible picture quality.  
CAUTION: Before making any connections to the AVR, ensure that the AVR’s AC  
power cord is unplugged from the AVR and the AC outlet. Making connections  
with the AVR plugged in and turned on could damage the speakers.  
tV  
Connect Your Speakers  
After you have placed your loudspeakers in the room as explained in Place Your Speakers,  
on page 8, connect each speaker to its color-coded terminal on the AVr as explained  
in Speaker Connections, on page 9. connect the speakers as shown in the illustration.  
hdmI cable  
(not supplied)  
AVr hdmI  
monitor out  
connector  
Composite Video Monitor Out connector  
If your tV does not have an hdmI connector, or if your tV does have an hdmI connector  
but you are connecting some source devices with only composite video connectors, use  
a composite video cable (not included) to connect the AVr’s composite monitor out  
connector to your tV’s composite video connector.  
IMPORTANT: the AVr’s on-screen display (oSd) only appears through the composite  
monitor out connector. If you want to use the AVr’s oSd menus you need to connect  
its composite monitor out connector to your tV even if you are not connecting any  
composite video source devices to the AVr.  
AVr composite  
monitor out  
connector  
tV  
c
fl  
fr  
composite Video cable  
(not supplied)  
Connect Your Source Devices  
Source devices are components where a playback signal originates, such as a  
blu-ray disc or dVd player, or a cable, satellite or hdtV tuner. your AVr has several  
different types of input connectors for your audio and video source devices: hdmI,  
composite video, optical digital audio, coaxial digital audio and analog audio.  
Sl  
Sr  
each of your AVr’s source buttons is assigned to an hdmI connector or an analog audio  
input connector (listed in the “AVr Source button/Analog Audio connector” column of  
the table below).the digital inputs are not assigned to any specific sets of analog inputs.  
once you select a source device you can use the remote control’s Audio Input Select  
(dIgItAl) button to select the specific audio input connection (hdmI, coaxial digital,  
optical digital, analog) that you want to listen to. (note: you cannot select an audio input  
connection for the fm/Am or uSb source buttons.)  
Connect Your Subwoofer  
use a single rcA audio cable to connect the AVr’s Subwoofer out connector to your  
subwoofer. consult your subwoofer’s user manual for specific information about making  
connections to it.  
powered  
Subwoofer  
As you connect your various source components, fill out the “Source device connected”  
and “digital Audio Input connector used” columns in the following table – it will make it  
easy to keep track of which devices you have connected to which connectors. note: the  
AVr remote is pre-programmed to control a harman/kardon blu-ray disc or dVd player  
connected to hdmI 1.  
Single  
rcA Audio cable  
(not supplied)  
AVR Source Button/  
Analog Audio Connector  
Digital Audio Input  
Connector Used  
AVr  
Subwoofer  
connector  
Source Device Connected  
Video 1  
Video 2  
Video 2  
tape  
Aux  
AVR Source Button/  
HDMI Connector  
Digital Audio Input  
Connector Used  
Source Device Connected  
*hdmI 1  
hdmI 2  
hdmI 3  
*the AVr remote is pre-programmed to control a harman/kardon blu-ray disc or dVd player  
connected to hdmI 1.  
11  
 
AVR 700/AVR 70/AVR 70C  
Making Connections, continued  
HDMI devices  
Optical digital audio devices  
If any of your source devices have hdmI connectors, using those connectors will provide  
the best possible video and audio performance quality. Since the hdmI cable carries  
both digital video and digital audio signals, you do not have to make any additional audio  
connections for devices you connect via hdmI cables.  
If your source devices have optical digital outputs, connect them to the AVr’s optical  
digital Audio connectors. note: make only one type of digital connection (hdmI, optical  
or coaxial) from each device.  
AVr digital Audio  
connectors  
• The AVR remote control is pre-programmed to control a Harman/Kardon Blu-ray Disc  
or dVd player when the hdmI 1 Source Selector button is pressed.  
If you have a tV equipped with the hdmI Audio return channel function, its sound is fed  
to the AVr via the hdmI out connector’s Audio return channel, and it will not require  
additional audio connections to the AVr.  
AVr hdmI  
connectors  
optical digital Audio  
cable (not supplied)  
to optical digital  
Audio output  
optical-equipped  
Source device  
hdmI cable  
(not supplied)  
Coaxial digital audio devices  
to hdmI  
output  
If your source devices have coaxial digital outputs, connect them to the AVr’s coaxial  
digital Audio connectors. note: make only one type of digital connection (hdmI, optical  
or coaxial) from each device.  
hdmI-equipped Source device  
AVr digital Audio  
connectors  
Composite video devices  
you will need to make composite video connections from your source devices that do  
not have hdmI connectors. you will also need to make an audio connection from the  
device to the AVr.  
AVr component  
Video connectors  
coaxial digital Audio  
cable (not supplied)  
to coaxial digitial  
Audio output  
composite Video  
cable (not supplied)  
coaxial digital-equipped  
Source device  
to composite  
Video output  
Analog audio devices  
make analog audio connections from your source devices that do not have hdmI or  
digital audio connectors. If you’re connecting video sources to the Video 1, Video 2 or  
Video 3 audio inputs, you must also connect the source device’s composite video output  
to the corresponding composite video connector.  
composite Video-equipped  
Source device  
AVr Analog Audio  
connectors  
Stereo Audio cable  
(not supplied)  
to Stereo Analog  
Audio output  
Analog Source device  
12  
 
AVR 700/AVR 70/AVR 70C  
Making Connections, continued  
Audio recorders  
Connect to AC Power  
connect an analog audio recorder’s inputs to the AVr’s analog audio tape out connectors.  
you can record any analog audio input signal except for the tape 1 input.  
connect the Ac power cord to the AVr’s Ac Input connector and then to a working Ac  
power outlet.  
AVr Analog Audio  
recorder connectors  
AVr Ac  
Input connector  
Ac power  
outlet  
power cord  
(supplied)  
Stereo Audio cable  
(not supplied)  
to Stereo Analog  
record Inputs  
Install the Batteries in the Remote Control  
remove the remote control’s battery cover, insert the three supplied AAA batteries as  
shown in the illustration, and replace the battery cover.  
Analog recording device  
Video recorders  
connect an analog video recorder’s video input connector to the AVr’s Video 1 out  
composite Video connector, and its audio input connectors to the AVr’s Video 1 out  
Analog Audio connectors. you can record the Video 2 or Video 3 composite video input  
signals.  
AVr Analog  
Audio connectors  
AVr composite  
Video connectors  
note: remove the protective plastic from the AVr’s front panel to keep it from reducing  
the remote control’s effectiveness.  
to Analog Audio/  
Video record Inputs  
Analog Audio/Video  
cable (not supplied)  
Analog Video  
recording device  
Connect the Radio Antennas  
• Connect the supplied FM antenna to the AVR’s FM 75Ω radio Antenna connector. for  
the best reception, extend the fm antenna as far as possible.  
• Bend and fold the base of the supplied AM antenna as shown and connect the  
antenna wires to the AVr’s Am and gnd connectors. rotate the antenna as necessary  
to minimize background noise.  
AVr Antenna  
connectors  
fm Antenna (supplied)  
Am Antenna  
(supplied)  
bend and fold base  
13  
 
AVR 700/AVR 70/AVR 70C  
Set Up the AVR  
Configure the AVR for Your Speakers  
1. turn on your tV and select the tV’s composite video input where you connected the  
AVr in Connect Your TV or Video Display, on page 11.  
Set Up the AVR  
Turn On the AVR  
2. press the remote control’s Setup button. the AVr’s on-screen display (oSd) System  
Setup menu will appear on the tV.  
1. Set the front-panel main power switch to “on.” (the front-panel Standby indicator  
will glow amber.)  
2. press the front-panel on/Standby switch.  
Standby  
Indicator  
Stereo  
Surr.Select  
Tuning  
AM/FM  
Preset  
Source  
Memory  
Folder  
Power  
Phones  
USB  
500A  
Video  
L
Audio  
R
5V  
Video  
3
3. use the remote’s arrow and ok buttons to select “Speaker Setup.” the Speaker Setup  
menu will appear.  
main power  
Switch  
on/Standby  
button  
unless you will not be using the AVr for an extended period of time, leave the main power  
switch set to “on.” when the main power switch is turned off, any settings you have  
programmed will be preserved for up to two weeks.  
IMPORTANT NOTE: If the PROTECT message ever appears in the Message  
display, turn off the AVR and unplug it. Check all speaker wires for a short  
circuit (“+” and “–” wires touching). If none is found, bring the unit to an  
authorized Harman Kardon service center for inspection and repair before  
using it again.  
4. Select “Speaker Settings.” the Speaker Settings menu will appear.  
Using the On-Screen Menu System  
Although it’s possible to configure the AVr using only the remote and the front-panel  
message display, it is easier to use the on-screen menu system.  
5. use the remote’s left and right arrow buttons to select off, SmAll or lArge for the  
front, center and Surround speaker positions, depending on the speakers you have  
connected to the receiver.  
to access the menu system, turn on your tV and select the tV’s composite video input  
where you connected the AVr in Connect Your TV or Video Display, on page 11.  
press the remote control’s Setup button. the AVr’s on-screen display (oSd) System  
Setup menu will appear on the tV.  
off: Select this setting if you have not connected a speaker in that position (not available  
for the front speakers).  
SmAll: Select this setting if the speaker is not capable of producing clean, deep bass  
energy at output levels that match those produced by a powered subwoofer. All bass  
below the crossover frequency (see Step 6, below) in that channel is removed from that  
speaker and is sent to the subwoofer (or to the front speakers if Subwoofer is set to no).  
most speakers (unless they are large and powerful) should be considered SmAll.  
lArge: Select this setting if the speaker is capable of producing clean, deep bass energy  
at output levels that match those produced by a powered subwoofer. All bass in that  
channel is sent to that speaker.  
the System Setup menu consists of five submenus: Speaker Set, hdmI Set, parameter,  
Auto power control and Speaker on/off.  
note: If your system has a subwoofer and you set the front speakers to lArge, the  
subwoofer may not output audio except for dolby digital- and dtS-encoded program  
material that contains lfe channel information. If you set your front speakers to lArge  
and you want your subwoofer to reproduce bass from all program material, set the  
Subwoofer to pluS (see below).  
use the up/down/left/right buttons on the remote to navigate the menu system, and  
press the ok button to select a menu or setting line, or to enter a new setting.  
the current menu, setting line or setting will appear in the front-panel message display,  
as well as on screen.  
for Subwoofer, select yeS (if your system has a subwoofer), no (if your system does not  
have a subwoofer), or pluS (if your system has a subwoofer, you set your front speakers  
to lArge and you want your subwoofer to reproduce bass from all program material).  
to return to the previous menu, press the remote’s bAck button. to exit the menu  
system, press the Setup button.  
follow the instructions in this Set Up the AVR section to configure your home theater  
system. you may return to these menus at any time to make additional adjustments.  
when you’re finished, record your settings in table A2 of the Appendix, on page 21, then  
press the remote control’s bAck button to return to the Speaker Setting menu.  
before you begin initial setup, all loudspeakers, a video display and all source devices  
should be connected to the AVr. you should be able to turn on the AVr and view the  
System Setup menu when you press the Setup button. If necessary, reread the Making  
Connections section and the beginning of this section before continuing.  
6. (note: If your system does not have a subwoofer, skip to step 7.) press the bAck button  
and select “crossover.” the crossover menu will appear  
14  
 
AVR 700/AVR 70/AVR 70C  
Set Up the AVR, continued  
consult the technical specifications for your system’s main left and right speakers and  
locate the frequency response, usually given as a range, e.g., 80hz – 20khz ( 3db).  
note the lowest frequency that the speakers are capable of playing (80hz in the above  
example). note: this frequency is not the same as the crossover frequency that may  
also be listed in the specifications.  
Notes on Setting Subwoofer Volume:  
• Sometimes the ideal subwoofer volume setting for music is too loud for films, while  
the ideal setting for films is too quiet for music. when setting the subwoofer volume,  
listen to both music and films with strong bass content and find a “middle ground”  
volume level that works for both.  
use the remote’s left and right arrow buttons to select the crossover frequency that  
most closely matches the low frequency specification that you noted above. the AVr  
will divide the source signal at this crossover point, will send all information above the  
crossover point to your system’s speakers, and all information below the crossover point  
to the subwoofer. this way, each loudspeaker in your system will perform at its best,  
delivering a more powerful and enjoyable sound experience. record the setting in table  
A2 of the Appendix, on page 21.  
• If your subwoofer always seems too loud or too quiet, you may want to place it in  
a different location. placing the subwoofer in a corner will always tend to increase  
its bass output, while placing it away from any walls or corners will always tend to  
lessen its bass output.  
13. when you’re finished, record the settings in table A3 of the Appendix, on page 21,  
then press the remote’s Setup button to turn off the on-screen menus.  
7. press the bAck button and select “Speaker distance.” the Speaker distance menu  
will appear.  
Additional Setup Menu Items  
you can also adjust the following settings:  
HDMI Set: Selecting Arc/cec on will send audio from the tV to the AVr via the hdmI  
Audio return channel (Arc) connection (which is in the hdmI cable connecting the AVr  
to the tV). this way, whenever you’re watching a source that is connected directly to  
your tV (such as an Internet connection), you can listen to the sound through the AVr by  
selecting tV as the AVr source device. Selecting on also allows the communication of  
control information among the hdmI devices in your system (cec).  
Audio Settings: Selecting Audio Settings allows you to adjust the following audio  
settings:  
• Night Mode works with specially encoded Dolby® digital discs or broadcasts,  
compressing the audio so that louder passages are reduced in volume to avoid  
disturbing others, while dialogue remains intelligible. press the left/right arrow  
buttons to advance through the following drc (dynamic range control) settings:  
8. measure the distance from each speaker in your system to the listening position.  
record the distances in table A3 of the Appendix, on page 21.  
9. use the remote’s left and right arrow buttons to change the distance setting for each  
speaker so it matches the distance you wrote down in step 8. when you’re finished,  
press the remote control’s bAck button to return to the Speaker Setting menu.  
off: no compression is applied. loud passages in the program remain as they were  
recorded.  
10. Select “channel level.” the channel level menu will appear. use the remote’s left  
and right arrow buttons to set test tone to “manual” and press the remote’s ok  
button. After the on-screen countdown you will hear test noise through the front left  
speaker.  
mid: loud passages in the program are reduced moderately in volume.  
max: loud passages in the program are reduced more in volume.  
Auto: Automatically compresses the audio a specific amount in response to  
instructions encoded in the dolby digital program.  
• PLII Music: Additional adjustments are avalable that allow you to fine-tune the Dolby  
pro logic II music surround mode’s performance for your listening room and personal  
taste:  
panorama: with the panorama mode turned on, some of the sound from the front  
speakers is moved to the surround speakers, creating an enveloping “wraparound”  
effect. each press of the left or right arrow buttons toggles the setting on or off.  
11. Sit in the main listening position and adjust the AVr’s volume control so the test noise  
is moderately loud. note the volume of the test noise through the first speaker. press  
the remote’s down arrow button to advance the test noise to each of your system’s  
speakers and note the volume level of the noise in each speaker.  
center width: this setting affects how vocals sound through the three front speakers.  
A lower number focuses the vocal information tightly on the center channel. higher  
numbers (up to 7) broaden the vocal soundstage. use the left/right arrow buttons to  
adjust this setting.  
12. As you advance the test noise through the speakers, use the remote’s left and right  
arrow buttons to adjust the volumes of the channels until all of them play at the  
same volume.  
dimension: this setting affects the depth of the surround presentation, allowing you  
to “move” the sound toward the front or rear of the room. the setting of “0” is a  
neutral default. “+” settings move the sound toward the front of the room, while “–”  
settings move the sound toward the rear. use the left/right arrow buttons to adjust it.  
Notes on Setting Speaker Volumes in Home Theater Systems:  
while setting your system’s individual speaker volume levels is ultimately up to your  
personal taste, here are some ideas you may find helpful:  
• For films and video-music programs, your overall goal should be to create an  
enveloping, realistic sound field that draws you into the film or music program  
without drawing your attention away from the action on the screen.  
See Audio Processing and Surround Sound, on page 17, for more information about  
dolby pro logic II.  
Auto Power Control: this setting allows you to set the AVr to automatically enter the  
Standby mode after a period of inactivity, saving energy. the available settings are off  
(default), 2 hours, 4 hours and 6 hours.  
• For multichannel music recordings, some music producers will create a sound field  
that places the musicians all around you; others will create a sound field that places  
the musicians in front of you, with more subtle ambience in the surround speakers  
(as you would experience in a concert hall).  
Speaker On/Off: use this setting to turn the speakers off when you are listening through  
headphones.  
• In most 5.1-channel film soundtracks, the surround speakers are not intended to be  
as loud or as active as the front speakers. Adjusting the surround speakers so they  
are always as loud as the front speakers could make dialogue difficult to understand  
and will make some sound effects sound unrealistically loud.  
15  
 
AVR 700/AVR 70/AVR 70C  
Operating Your AVR  
In the fm Stereo mode, the radio uses automatic tuning, meaning each press of the  
tuning up/down buttons scans until a station with acceptable signal strength is found. In  
the fm mono mode, the radio uses manual tuning, in which each press of a tuning button  
steps through a single frequency increment. (using the fm mono mode may improve the  
reception of weaker stations.)  
Operating Your AVR  
now that you have installed your components and completed a basic configuration, you  
are ready to begin enjoying your home theater system.  
Controlling the Volume  
Preset Stations  
Adjust the volume either by turning the front-panel Volume knob (clockwise to increase  
volume or counterclockwise to decrease volume) or by pressing the Volume up/down  
buttons on the remote.  
A total of 30 stations (Am and fm combined) may be stored as presets. when the desired  
station has been tuned in, press the memory button and the preset number will flash on  
the front-panel message display. use the remote’s number buttons to enter the desired  
preset number.  
Muting the Sound  
to tune a preset station, press the preset up/down buttons or enter the preset number  
using the remote’s number buttons.  
to mute all speakers and the headphones, press the mute button on the remote. Any  
recording in progress will not be affected. the mute message will appear in the front-  
panel display as a reminder. to restore the sound, press the mute button again, or adjust  
the volume.  
Listening to Media on a USB Device  
your AVr is compatible with uSb 2.0 or uSb 1.1 media in the fAt 16 or fAt 32 file format  
and is compatible with the following mp3 and wmA media:  
Listening Through Headphones  
plug the 1/4-inch stereo plug on a pair of headphones into the front-panel phones jack for  
private listening. note: for information about turning off the speakers during headphone  
listening, see Additional Setup Menu Items – Speaker On/Off, on page 15.  
• MP3: Bit rates between 96 – 320kbps. Fixed bit-rates at 44.1kHz sampling is  
recommended. Variable bit-rates (Vbr) are playable, but playing time may be  
displayed incorrectly. files must have a “.mp3” file extension.  
• WMA: Bit rates of 64kbps or higher. NOTE: Bit rates of 80kbps and 256kbps are not  
compatible. files must have a “.wma” file extension.  
Selecting a Source  
there are two different ways to select a source:  
• Press the front-panel Source Select buttons.  
• Directly select any source by pressing its Source Selector button on the remote.  
A maximum number of 65,536 folders and files can be supported.  
Playing files on a USB device  
1. Insert the uSb drive into the AVr’s front-panel uSb port. ImportAnt: do not connect a  
personal computer or peripheral to the uSb port. uSb hubs are not supported.  
the AVr selects the analog audio and video inputs assigned to the source and any other  
settings you made during setup.  
2. Select uSb as the source device. “uSb” will appear on the front-panel display, and  
after the AVr loads the contents of the current folder the uSb playback screen will  
appear on the oSd.  
the digital audio inputs are not assigned to any specific sets of analog inputs. once you  
select a source device you can use the remote control’s Audio Input Select (dIgItAl)  
button to select the specific audio input connection (hdmI, coaxial digital, optical digital,  
analog) that you want to listen to. (note: you cannot select an audio input connection for  
the fm/Am or uSb source buttons.)  
file playback  
type mode  
repeat  
mode  
the source name, the selected audio input and the surround mode will appear on the  
front panel.  
Song title  
Video Troubleshooting Tips  
If there is no picture:  
Artist name  
Album title  
• Check the source selection.  
• Check all connections for a loose or incorrect connection.  
• Check the video-input selection on the TV/display device.  
Additional Tips for Troubleshooting HDMI Connections  
• Turn off all devices (including the TV, the AVR and any source components).  
data  
rate  
elapsed  
time  
use the remote’s transport control buttons to control playback.  
• Unplug the HDMI cables, starting with the cable between the AVR and the TV, and  
continuing with the cables between the AVr and each source device.  
to browse the contents of the current folder, press the remote’s bAck button. the uSb  
folder screen will appear on the oSd for 20 seconds.  
• Carefully reconnect the cables from the source devices to the AVR. Connect the  
cable from the AVr to the tV last.  
• Turn on the devices in this order: TV, AVR, source devices.  
NOTE: Depending upon the particular components involved, the complexity of  
the required communication between HDMI components may cause delays of  
up to a minute in the completion of some actions, such as input switching or  
switching between SD and HD channels.  
Listening to FM and AM Radio  
Select the Am/fm source. use the tuning up/down buttons to tune a station, which will  
be shown on the front-panel display and the tV screen.  
use the remote’s up, down and ok buttons to highlight and select tracks.  
IMPORTANT: to prevent damage or malfunction, press the remote’s Stop (■) transport  
control button before removing the uSb device from the AVr’s uSb port.  
16  
 
Operating Your AVR, continued,  
and Advanced Functions  
AVR 700/AVR 70/AVR 70C  
Surround Mode Selection  
Selecting a Surround Mode  
Surround-mode selection depends upon the format of the incoming audio signal as well  
as your personal taste. Although there is never a time when all of the AVr’s surround  
modes are available, the table below indicates which surround modes are available for  
a given input.  
Selecting a surround mode can be as simple or sophisticated as your individual system  
and tastes. feel free to experiment, and you may find a few favorites for certain sources  
or program types. you can find more detailed information on surround modes in Audio  
Processing and Surround Sound, below.  
to select a surround mode, press the Surround mode Select buttons. each press  
advances to the next available surround mode.  
Input Signal Format  
Available Surround Modes  
dolby true hd,  
dolby digital plus,  
dolby digital  
corresponding dolby true hd or dolby digital mode  
(theater, hall, Stadium, club, Arena and 5-ch Stereo  
are also available for 5.1-channel programs)  
digital surround-sound modes, such as dolby digital and dtS systems, are available only  
with specially encoded programs, such as those available via hdtV, dVd and blu-ray  
disc media and digital cable or satellite television. other surround modes such as dolby  
pro logic II may be used with digital or analog signals to create a different surround  
presentation or to use a different number of speakers.  
(7.1-channel/5.1-channel)  
dolby digital (2.0-channel)  
dolby pro logic II movie, dolby pro logic II music,  
dolby pro logic II game, dolby pro logic  
Surround mode selection depends upon the number of speakers in your system, the  
programs you are watching or listening to, and your personal tastes.  
dtS hd master Audio,  
dtS, dtS 96/24  
corresponding dtS mode (theater, hall, Stadium,  
club, Arena and 5-ch Stereo are also available for  
5.1-channel programs)  
Advanced Functions  
pcm (2-channel),  
Analog (2-channel)  
dolby pro logic II movie, dolby pro logic II music,  
dolby pro logic II game, dolby pro logic, dtS neo:6  
cinema, dtS neo:6 music, theater, hall, Stadium,  
club, Arena, 5-ch Stereo  
much of the adjusting and configuration your AVr requires is handled automatically, with  
little intervention required on your part. you can also customize your AVr to suit your  
system and your tastes. In this section, we will describe some of the more advanced  
adjustments available to you.  
mp3/wmA  
dolby pro logic II movie, dolby pro logic II music,  
dolby pro logic II game, dolby pro logic, dtS neo:6  
cinema, dtS neo:6 music, theater, hall, Stadium,  
club, Arena, 5-ch Stereo  
Audio Processing and Surround Sound  
Audio signals can be encoded in a variety of formats that affect not only the quality of the  
sound but also the number of speaker channels and the surround mode. you may also  
manually select a different surround mode, when available.  
when in doubt, check the broadcast or the jacket of your disc for more information  
on which surround modes are available. usually, nonessential sections of a disc, such  
as trailers, extra materials or the disc menu, are available only in dolby digital 2.0  
(2-channel) or pcm 2-channel mode. look for an audio setup section in the disc’s menu.  
Also, make sure your disc player’s audio output is set to the original bitstream rather than  
2-channel pcm. Stop play and check the player’s output setting.  
Analog Audio Signals  
Analog audio signals usually consist of two channels – left and right. your AVr offers  
several options for analog playback:  
• Stereo: When you want conventional 2-channel playback, press the STEREO button.  
Sound will be output from the front left and right speakers.  
Adjusting the Channel Volumes  
In addition to using the AVr’s built-in test noise to configure the AVr for your speakers as  
explained in Configure the AVR for Your Speakers, you can also adjust the volume of any  
channel at any time to compensate for individual program sources or your personal taste.  
• 5-Ch Stereo: When you want to hear stereo sound through all of the system’s speakers  
(such as during a party), select 5ch Stereo via the Surround mode Select buttons.  
this plays the left-channel signal through the front left and surround left speakers,  
the right-channel signal through the front right and surround right speakers, and a  
summed mono signal through the center speaker.  
1. press the remote’s channel level button. the message display will show the left  
channel volume level.  
• Analog Surround Modes: Your AVR is able to process 2-channel audio signals to  
produce multi-channel surround sound, even when no surround sound has been  
encoded in the recording. Among the available modes are dolby pro logic II, dolby  
pro logic, dtS neo: 6, theater, hall, Stadium, club and Arena modes. use the  
Surround mode Select buttons to select one of these modes. See table A5 in the  
Appendix, on page 25, for breif explanations of each of these surround modes.  
2. use the remote’s up and down arrow buttons to display the channel you want to adjust.  
3. use the remote’s left and right arrow buttons to adjust the channel’s volume.  
press the bAck button when you’re finished.  
Digital Audio Signals  
Recording  
digital audio signals offer greater flexibility and capacity than analog signals and  
allow the encoding of up to 5.1 channels of discrete channel information directly into  
the signal. the result is improved sound quality and startling directionality, since each  
channel’s information is transmitted independently of the other channels. high-resolution  
recordings sound extraordinarily distortion-free, especially in the high frequencies.  
two-channel analog audio signals, as well as composite video signals, are normally  
available at the appropriate recording output connectors. to make a recording, connect  
your audio or video recorder to the appropriate AVr output connectors as described in  
the Making Connections section, insert blank media in the recorder and make sure the  
recorder is turned on and recording while the source is playing. refer to the recording  
device’s instructions for complete information about making recordings.  
digital surround-sound formats include dolby digital 2.0 (two channels only), dolby  
digital 5.1, dolby digital ex (6.1), dolby digital plus (7.1), dolby truehd (7.1), dtS-  
hd high-resolution Audio (7.1), dtS-hd master Audio (7.1), dtS 5.1, dtS 96/24 (5.1),  
2-channel pcm modes in 44.1khz, 48khz, 88.1khz, 96khz or 176.4khz, and 5.1 or  
7.1 multichannel pcm. (your AVr will downmix the discrete surround back-channel  
information in 6.1-channel and 7.1-channel recordings into your system’s surround left  
and surround right channels.)  
noteS:  
1. the AVr does not convert digital signals to analog. only devices connected to the  
analog audio and composite video input connections can be recorded.  
2. hdmI video sources are not available for recording.  
3. please make certain that you are aware of any copyright restrictions on any material  
you record. unauthorized duplication of copyrighted materials is prohibited by law.  
17  
 
AVR 700/AVR 70/AVR 70C  
Advanced Functions, continued  
To reset the AVR’s processor:  
Sleep Timer  
1. press the front-panel Standby/on switch to place the unit in the Standby mode (the  
Standby Indicator led will turn amber).  
the sleep timer sets the AVr to play for up to 90 minutes and then turn off automatically.  
press the Sleep button on the remote, and the time until turn-off will be displayed on  
the front-panel message display the available settings are 30 min., 60 min., 90 min.  
and off.  
2. press and hold the front-panel Standby and memory/folder buttons until the reSet  
message appears on the front-panel message display.  
3. press the memory/folder button again to reset the AVr’s processor.  
when the sleep timer has been set, a small crescent-moon icon will appear on the front-  
panel display.  
If the AVr does not function correctly after a processor reset, contact an authorized  
harman kardon service center for assistance. to locate an authorized service center,  
visit our web site at www.harmankardon.com.  
If you press the Sleep button after the timer has been set, the remaining play time will be  
displayed. press the Sleep button again to change the play time.  
Memory  
Processor Reset  
If the AVr is unplugged or experiences a power outage, it will retain your user settings  
for up to two weeks.  
If the AVr behaves erratically after a power surge, first turn off the front-panel main  
power switch and unplug the Ac power cord for at least 3 minutes. plug the cord back  
in and turn the AVr on. If this procedure doesn’t help, reset the AVr’s processor as  
described below.  
note: resetting the processor will erase all user configurations, including speaker and  
level settings, and tuner presets. After a reset, reenter all of these settings from your  
notes in the Appendix worksheets.  
18  
 
AVR 700/AVR 70/AVR 70C  
Troubleshooting  
Troubleshooting  
Symptom  
Cause  
Solution  
unit does not function when main power switch is  
turned on  
• No AC power  
• Ensure that the power cord is plugged into a live AC  
power outlet  
• Check if the AC outlet is switch-controlled  
front-panel message display lights, but there's no  
sound or picture  
• Intermittent input connection  
• Mute is on  
• Secure all input and speaker connections  
• Press Mute button  
• Volume control is turned down  
• Turn up Volume control  
no sound from any speaker  
• Speakers set to “Off” in System Setup menu  
• Set speakers to “On” in System Setup menu. See  
Additional Setup Menu Items: Speaker On/Off, on  
page 15, for more information.  
no sound from any speaker; protect message  
appears on message display  
• Amplifier is in protection mode due to possible short  
circuit  
• Check all speaker wires at speaker and AVR  
connections for crossed wires  
• Amplifier is in protection mode due to internal problems  
• Contact your local Harman Kardon service center  
no sound from center or surround speakers  
• Incorrect surround mode  
• Select a surround mode other than stereo  
• Program material is monophonic  
• Incorrect speaker configuration  
• Program material is stereo  
• Mono programs contain no surround information  
• Check the speaker configuration in the setup menu  
• The surround decoder may not create center- or  
surround-channel information from nonencoded stereo  
programs  
unit does not respond to remote control commands  
Intermittent buzzing in tuner  
• Weak batteries in remote  
• AVR not selected  
• Change batteries in remote  
• Press the Setup/AVR button  
• Remote sensor is obscured  
• Ensure that the AVR’s front-panel remote sensor is in  
the line of sight of the remote  
• Local interference  
• Move the AVR or antenna away from computers,  
fluorescent lights, motors or other electrical appliances  
Additional information on troubleshooting possible problems with your AVr and installation-related issues may be found in the list of “frequently Asked Questions,” which is located in the product  
Support section of our web site: www.harmankardon.com  
19  
 
AVR 700/AVR 70/AVR 70C  
Specifications  
Specifications  
Audio Section  
Video Section  
multichannel power:  
75w per channel, two  
channels driven @ 6  
ohms, 20hz – 20khz,  
<0.1% thd;  
100w per channel, two  
channels driven @ 6  
ohms, 1khz, <1% thd  
television format:  
ntSc (AVr 700);  
pAl (AVr 70/AVr 70c)  
Input level/impedance:  
output level/impedance:  
Video frequency response (composite video):  
hdmI:  
1Vp-p/75 ohms  
1Vp-p/75 ohms  
10hz – 8mhz (–3db)  
with 3d and deep color  
Input sensitivity/impedance:  
200mV/47k ohms  
95db  
Signal-to-noise ratio (Ihf-A):  
Surround system adjacent-channel separation:  
dolby pro logic/plII:  
40db  
General Specifications  
dolby digital: 55db  
dtS: 55db  
power requirement:  
120V Ac/60hz (AVr 700)  
220V Ac/50hz (AVr 70)  
230V Ac/50hz (AVr 70c)  
frequency response:  
10hz – 100khz  
25 amps  
high instantaneous-current capability (hcc):  
power consumption:  
dimensions (w x h x d):  
weight  
<0.5w (standby);  
280w maximum  
17-5/16" x 4-5/16" x 13"  
(440mm x 125mm x 330mm)  
FM Tuner Section  
20 lb (9.1kg)  
frequency range:  
87.5 – 108.0mhz  
1.3µV/13.2dbf  
65db/62db  
0.2%/0.3%  
35db @ 1khz  
80db  
usable sensitivity Ihf:  
Signal-to-noise ratio (mono/stereo):  
distortion (mono/stereo):  
Stereo separation:  
Image rejection:  
If rejection:  
80db  
AM Tuner Section  
frequency range:  
520 – 1720khz  
45db  
Signal-to-noise ratio:  
usable sensitivity (loop):  
Selectivity ( 10khz):  
500µV  
30db  
20  
 
AVR 700/AVR 70/AVR 70C  
Appendix  
Appendix – Default settings, worksheets, remote product codes  
Table A1 – Recommended Source Component Connections  
Device Type  
AVR Source  
Audio Connections  
Video Connections  
Vcr, dVr, pVr, or other audio/video recorder  
Video 1  
• Video 1 Analog (inputs and outputs)  
• Composite Video 1 Input  
• For recording, use Composite Video 1 Output  
Video 2  
• Video 2 Analog inputs  
• Optical 1 Input (if not in use)  
• HDMI 1 Input  
composite Video 2 Input  
cable tV, Satellite, hdtV or other device that  
delivers television programs  
blu-ray disc player  
hdmI 1  
hdmI 2  
• HDMI 1 Input  
• HDMI 2 Input  
hdmI-capable disc player, game console or  
other audio/video device  
• HDMI 2 Input  
• HDMI 3 Input  
hdmI-capable disc player, game console or  
other audio/video device  
hdmI 3  
• HDMI 3 Input  
Video 3  
Aux  
• Video 3 Analog Audio Input on front panel  
• Aux Analog Inputs  
• Video 3 Coaxial Video Iinput on front panel  
• Not required  
portable audio device, camcorder, game console  
cd player  
• Any one available coaxial or optical digital audio  
input  
tape  
• Tape Analog (inputs and outputs)  
• Not required  
cd-r, minidisc, cassette  
note: table A1 is a guideline; you may need to make adjustments to fit your system.  
Table A2 – Speaker/Channel Settings  
Source  
Speaker Setting  
left/right Speaker  
center Speaker  
Surround Speakers  
Subwoofer  
crossover  
Table A3 – Speaker Volume and Distance Settings  
Your Distance From Speaker  
to Listening Position  
Speaker Positions  
Channel Volume Setting  
front left  
center  
front right  
Surround right  
Surround left  
Subwoofer  
21  
 
AVR 700/AVR 70/AVR 70C  
Appendix  
Table A4 – Surround Modes  
Surround Mode  
Description  
Incoming Bitstream or Signal  
• Dolby Digital 1/0/.0 or .1, 2/0/.0 or .1, 3/0/.0 or .1,  
2/1/.0 or .1, 2/2/.0 or .1, 3/2/.0 or .1  
dolby digital  
provides up to five separate main audio channels and a dedicated low-frequency  
effects (lfe) channel.  
• Dolby Digital EX (played as 5.1)  
• Dolby Digital Plus decoded and delivered via coaxial or optical  
connection  
• Dolby Digital Plus via HDMI connection (source device decodes to  
dolby digital when a coaxial or optical connection is used)  
dolby digital plus  
An enhanced version of dolby digital encoded more efficiently, dolby digital plus  
has the capacity for additional discrete channels and for streaming audio from the  
Internet, all with enhanced audio quality. Source material may be delivered via an  
hdmI connection or decoded to dolby digital or pcm and transmitted via coaxial or  
optical digital audio.  
dolby truehd is an expansion of mlp lossless™ audio, the same format used on  
dVd-Audio discs. dolby truehd adds the features found in dolby digital, such as  
night mode settings, while delivering fully lossless audio that is a true reproduction  
of studio master recordings.  
• Blu-ray Disc or HD-DVD encoded with Dolby TrueHD, delivered  
via hdmI  
dolby truehd  
• Dolby Digital 1/0/.0 or .1, 2/0/.0 or .1, 3/0/.0 or .1,  
2/1/.0 or .1, 2/2/.0 or .1, 3/2/.0 or .1  
dolby digital Stereo  
delivers a 2-channel downmix of dolby digital materials.  
• Dolby Digital EX  
dolby pro logic II mode group  
dolby pro logic II movie  
Analog decoder that derives five full-range, discrete main audio channels from  
matrix surround-encoded or 2-channel analog sources. four variants are available.  
See below  
• Dolby Digital 2.0 or 2.1  
• Analog (two-channel)  
• Tuner  
Variant of dolby pro logic II that is optimized for movie and television programs.  
• PCM (32kHz, 44.1kHz, 48kHz, 96kHz)  
• MP3/WMA  
• Dolby Digital 2.0 or 2.1  
• Analog (two-channel)  
• Tuner  
dolby pro logic II music  
dolby pro logic II game  
dolby pro logic  
Variant of dolby pro logic II that is optimized for music selections. Allows  
adjustment of sound-field presentation in three dimensions:  
• Center Width (adjusts width of vocal soundstage)  
• Dimension (adjusts depth of soundstage)  
• PCM (32kHz, 44.1kHz, 48kHz, 96kHz)  
• MP3/WMA  
• Panorama (adjusts wraparound surround effect)  
• Dolby Digital 2.0 or 2.1  
• Analog (two-channel)  
• Tuner  
Variant of dolby pro logic II that emphasizes use of the surround channels and  
subwoofer for total immersion in the video gaming experience.  
• PCM (32kHz, 44.1kHz, 48kHz, 96kHz)  
• MP3/WMA  
• Dolby Digital 2.0 or 2.1  
• Analog (two-channel)  
• Tuner  
original version of dolby pro logic that steered a mono signal containing  
information below 7khz to the surround channels.  
• PCM (32kHz, 44.1kHz, 48kHz, 96kHz)  
• MP3/WMA  
using a different encoding/decoding method from dolby digital, dtS digital • DTS 1/0/.0 or .1, 2/0/.0 or .1, 3/0/.0 or .1, 3/1/.0 or .1, 2/2/.0 or  
dtS digital  
also provides up to five discrete main channels, plus an lfe channel.  
.1, 3/2/.0 or .1  
• DTS-ES Matrix (played as 5.1)  
• DTS-ES Discrete (played as 5.1)  
• Blu-ray Disc or HD-DVD discs encoded with DTS-HD modes,  
delivered via hdmI connection  
dtS-hd  
dtS-hd is a high-definition audio format that complements the high-definition video  
found on blu-ray disc and hd-dVd discs. It is transmitted using a dtS core with  
high-resolution extensions. even when only dtS 5.1 surround sound is desired (or  
available, if the multizone system is in use), the higher capacity of high-resolution  
discs serves up dtS at twice the bit rate used on dVd-Video discs.  
• Blu-ray Disc or HD-DVD discs encoded with DTS-HD Master  
Audio technology, delivered via hdmI connection  
dtS-hd master Audio  
dtS-hd master Audio technology delivers bit-for-bit reproductions of studio master  
recordings for an incredibly accurate performance.  
22  
 
AVR 700/AVR 70/AVR 70C  
Appendix  
Table A4 – Surround Modes (cont.)  
Surround Mode  
Description  
Incoming Bitstream or Signal  
• DTS 1/0/.0 or .1, 2/0/.0 or .1, 3/0/.0 or .1, 3/1/.0 or .1, 2/2/.0 or  
.1, 3/2/.0 or .1  
dtS Stereo  
delivers a 2-channel downmix of dtS digital materials or presents a matrix-  
encoded surround presentation.  
• DTS 96/24  
• DTS-ES Matrix  
dtS neo:6 cinema  
dtS neo:6 music  
theater  
delivers an enhanced 5.1-channel surround-sound experience for movies  
delivers an enhanced 5.1-channel surround-sound experience for music  
creates the effect of being in a large movie theater. works well with movies.  
• Analog (two-channel)  
• AM/FM radio  
• PCM (32kHz, 44.1kHz, 48kHz, 96kHz)  
• MP3/WMA  
• Analog (two-channel)  
• AM/FM radio  
• PCM (32kHz, 44.1kHz, 48kHz, 96kHz)  
• MP3/WMA  
• Analog (two-channel)  
• AM/FM radio  
• PCM (32kHz, 44.1kHz, 48kHz, 96kHz)  
• MP3/WMA  
hall  
creates the ambience of a concert hall. good when listening to classical music  
sources such as orchestral music, chamber music or instrumental soloists.  
• Analog (two-channel)  
• AM/FM radio  
• PCM (32kHz, 44.1kHz, 48kHz, 96kHz)  
• MP3/WMA  
Stadium  
creates an expansive soundfield as heard in stadiums. good for watching sporting  
events like baseball or soccer.  
• Analog (two-channel)  
• AM/FM radio  
• PCM (32kHz, 44.1kHz, 48kHz, 96kHz)  
• MP3/WMA  
club  
creates the ambience of a club with a low ceiling and hard wall surfaces. good for  
listening to jazz or other intimate musical ensembles.  
• Analog (two-channel)  
• AM/FM radio  
• PCM (32kHz, 44.1kHz, 48kHz, 96kHz)  
• MP3/WMA  
Arena  
creates a dynamic and broad soundspace that heightens the impact of film  
soundtracks and musical performances.  
• Analog (two-channel)  
• AM/FM radio  
• PCM (32kHz, 44.1kHz, 48kHz, 96kHz)  
• MP3/WMA  
• Analog (two-channel)  
• Tuner  
5-channel Stereo  
2-channel Stereo  
useful for parties, the left- and right-channel information is played through both  
the front and surround speakers on each side, while the center speaker plays a  
summed mono mix.  
• PCM (32kHz, 44.1kHz, 48kHz, 96kHz)  
• MP3/WMA  
• Analog (two-channel; DSP downmix available for multichannel)  
turns off all surround processing and plays a pure 2-channel signal or a downmix  
of a multichannel signal. the signal is digitized and bass management settings are  
applied, making it appropriate when a subwoofer is used.  
• Tuner  
• PCM (32kHz, 44.1kHz, 48kHz, 96kHz)  
• MP3/WMA  
23  
 
AVR 700/AVR 70/AVR 70C  
Appendix  
refer to the numbered buttons when using the remote control function list  
24  
 
AVR 700/AVR 70/AVR 70C  
Appendix  
Table A5 – Remote Control Function List  
No.  
01  
02  
03  
04  
05  
06  
07  
08  
09  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
Button Name  
power on  
power off  
mute  
AVR Function  
Blu-ray/DVD  
power on  
No.  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
43  
44  
45  
46  
47  
48  
49  
50  
51  
52  
53  
54  
55  
56  
57  
58  
Button Name  
AVR Function  
Blu-ray/DVD  
power on  
1
1
1
power off  
power off  
2
2
2
mute  
mute  
3
4
3
3
AVr  
AVr Select  
AVr Select  
4
4
hdmI 1  
hdmI 2  
hdmI 3  
uSb  
hdmI 1 Select  
hdmI 2 Select  
hdmI 3 Select  
uSb Select  
hdmI 1 Select  
hdmI 2 Select  
hdmI 3 Select  
uSb Select  
5
5
5
6
6
6
7
7
7
8
8
8
VId 1  
Video 1 Select  
Video 2 Select  
Video 3 Select  
radio Select  
Video 2 Select  
Video 2 Select  
Video 3 Select  
radio Select  
hdmI Arc Select  
Stereo mode Select  
tape Select  
9
9
9
VId 2  
0
0
preset memory  
tuning down  
tuning up  
preset tune down  
preset tune down  
Sleep timer  
display dimmer  
uSb repeat/ramdon  
----  
0
VId 3  
memory  
tuning down  
tuning up  
preset down  
preset up  
Sleep/cleAr  
dim  
find  
Am/fm  
tV  
program/red (bd)  
bookmark/green (bd)  
thumbnail/yellow (bd)  
Zoom/blue (bd)  
clear  
hdmI Arc Select  
Aux  
Aux  
tape  
tape Select  
Surr+  
Stereo  
tone  
Surr mode Select +  
Stereo mode Select  
tone controls  
Volume up  
Surr mode Select +  
Stereo mode Select  
home (bd)  
display dimmer  
repeat  
repeat/random  
Skip down  
Skip up  
reverse   
play   
forward   
open/close  
Stop  
Vol +  
Surr–  
dISplAy  
teSt  
Volume up  
previous  
Surr mode Select –  
display mode Select  
test tone on/off  
Volume down  
Input type Select  
Setup menu on/off  
move/Adust up  
move/Adjust left  
ok  
Surr mode Select –  
display mode Select  
pop-up menu  
Volume down  
options menu  
Settings (bd) Setup (dVd)  
up  
----  
next  
----  
reverse Search  
play/reverse  
forward Search  
open/close  
Stop  
----  
Vol–  
----  
dIgItAl  
Setup  
up  
----  
----  
pause  
----  
pause  
left  
left  
ok  
enter  
right  
move/Adjust right  
move/Adjust down  
previous menu  
channel level Adjust  
right  
down  
bAck  
down  
exit (bd)  
chAnnel  
top menu display (bd)  
25  
 
hArmAn International Industries, Incorporated  
8500 balboa boulevard, northridge, cA 91329 uSA  
© 2012 hArmAn International Industries, Incorporated. All rights reserved.  
harman kardon is a trademark of hArmAn International Industries, Incorporated, registered in the united States and/or other countries.  
blu-ray disc is a trademark of the blu-ray disc Association.  
ceA is a registered trademark of the consumer electronics Association.  
manufactured under license from dolby laboratories. dolby, the double-d symbol and pro logic are registered trademarks of dolby  
laboratories. mlp lossless is a trademark of dolby laboratories.  
manufactured under license under u.S. patent nos: 5,956,674; 5,974,380; 6,226,616; 6,487,535; 7,212,872; 7,333,929; 7,392,195;  
7,272,567 & other u.S. and worldwide patents issued &pending. dtS-hd, the Symbol, & dtS-hd and the Symbol together are registered  
trademarks of dtS, Inc. © dtS, Inc. All rights reserved.  
hdmI, the hdmI logo and high-definition multimedia Interface are registered trademarks of hdmI licensing llc in the united States and  
other countries.  
features, specifications and appearance are subject to change without notice.  
hkp4078 rev. 1  
www.harmankardon.com  
 

Graco Baby Accessories 1761213 User Manual
Graco Inc Pressure Washer 2545 User Manual
Graco Outboard Motor ti18496b User Manual
Harbor Freight Tools Pressure Washer 91142 User Manual
Honeywell All in One Printer 1250gAP User Manual
Hotpoint Microwave Oven 6640 User Manual
HP Hewlett Packard Stereo System 2138A User Manual
Huawei Cell Phone Y300 User Manual
IBM Computer Drive 22P7028 User Manual
Impex Fitness Equipment BF 1201 User Manual