Harman Kardon Speaker System HKSB30BLK User Manual

SB 30  
Multichannel active soundbar speaker system  
Owner’s Manual  
 
SB 30  
Introduction, Description and Features, and Included Items  
Introduction  
Included Items  
Thank you for purchasing the Harman Kardon SB 30 multichannel active soundbar  
speaker system, with which you’re about to begin many years of listening enjoyment.The  
SB 30 has been custom-designed to create an extraordinarily realistic cinema experience  
in your own living room.  
Carefully unpack your soundbar speaker system and confirm that all the items shown  
here are included.  
While extremely sophisticated electronics and state-of-the-art speaker components are  
hard at work within the SB 30, connecting, setting up and operating the system is simple.  
SB 30 CNTR  
Soundbar  
To obtain maximum enjoyment from your new speaker system, we urge you to take a  
few minutes to read through this manual. It will help ensure that the connections you  
make are correct. In addition, a few minutes spent learning the functions of the various  
controls will enable you to take advantage of all the power and refinement the SB 30 is  
able to deliver.  
If you have any questions about this product, its installation or its operation, please  
6.5-ft. (2m)  
Stereo Audio Cable  
Description and Features  
5-ft. (1.5m) Optical  
Digital Audio Cable  
The SB 30 is a complete home theater speaker system that includes:  
• A video-shielded soundbar speaker (the SB 30 CNTR) that features 13 speaker  
elements, 11 amplifier channels and a triple-core digital signal processor.  
SB 30 SUB  
Wireless  
Subwoofer  
• An 8-inch (200mm), 100-watt wireless powered subwoofer (the SB 30 SUB).  
• An IR remote control.  
AC Power Cord *  
(for Soundbar)  
* Power cord varies by region.  
• Wall-mount brackets for the soundbar.  
• An optical digital audio cable for connecting the system directly to your cable/  
satellite tuner or disc player.  
Rubber  
Feet  
Wall-Mount  
Brackets  
Remote  
Control  
• A 6-1/2-foot (2m) stereo audio cable for connecting the system directly to your TV’s  
audio output.  
IMPORTANT: If anything is missing, or if any part of your SB 30 system fails to operate  
properly, contact your dealer immediately.  
• A 3-foor (1.8m) AC power cord for the SB 30 CNTR soundbar.  
The SB 30 CNTR soundbar contains six 2-inch woofers and seven 1-inch tweeters,  
powered by four 40-watt amplifiers and seven 10-watt amplifiers. It features a powerful  
triple-core DSP (digital signal processor) with two HARMAN-exclusive surround modes  
(Virtual and HARMAN Wave – patent pending) that utilize different combinations of the  
soundbar’s 13 transducers and 11 amplifier channels to create an astonishingly realistic  
surround-sound experience in any size room and for listeners at any position in the room,  
without needing any extra speakers or wires.  
You can set the soundbar on a table in front of your TV, or, if you have a wall-mounted  
flat-panel TV, you can use the supplied brackets to mount the soundbar on the wall along  
with your flat-panel TV.  
The SB 30 SUB subwoofer receives its signal from the SB 30 CNTR soundbar via wireless  
technology, so you can place it anywhere in your room without having to run any wires  
between it and the soundbar. Its 8-inch (200mm) woofer and built-in 100-watt amplifier  
deliver the impact and excitement from your favorite movies and video games. Other  
conveniences include a volume control, a phase switch for fine-tuning bass performance  
to suit your listening environment, and an efficient switching system that senses the  
presence of an audio signal and automatically switches the subwoofer on.  
Sidney Harman and Bernard Kardon invented the high-fidelity receiver more than 50  
years ago. With state-of-the-art features and time-honored circuit designs, the SB 30  
system will turn your flat-panel TV into a fun and exciting home theater.  
3
 
SB 30  
Connections and Controls  
Connections and Controls  
Soundbar Rear-Panel Controls and Connectors  
Input  
Input  
L
1
2
3
4
Input  
Input  
Coaxial Digital  
Input Connector  
L
Optical Digital  
Input Connector  
1
2
3
4
Analog  
Input  
Connectors  
EQ  
Switch  
Wireless  
Code  
Switch  
Input  
Input  
L
1
2
3
4
Power Cord  
Connector  
Power  
Switch  
AC Fuse  
Holder  
Voltage  
Selector  
Switch  
Coaxial Digital Input connector: If your TV, disc player or cable/satellite tuner has a  
Power switch: Set this switch to the “On” position to put the soundbar into the Standby  
mode. In normal operation, this switch will be left in the “On” position. See Turning the  
Soundbar On and Off, on page 11, for more information.  
coaxial digital output, use a coaxial digital audio cable (not supplied) to connect it here.  
Optical Digital Input connector: If your TV, disc player or cable/satellite tuner has an  
optical digital output, use the supplied optical digital audio cable to connect it here.  
Voltage Selector switch: This switch is set at the factory for the proper AC voltage in  
the region where the soundbar is shipped. See Voltage Selector Switch, on page 9, for  
more information.  
Analog Input connectors: Use the supplied stereo audio cable to connect the stereo  
analog outputs of your TV, disc player or cable/satellite tuner here.  
AC Fuse holder: The SB 30 CNTR is factory-equipped with a T4AL/250V AC fuse (110 –  
120V AC operation) or a T2AL/250V AC fuse (220 – 240V AC operation). If the fuse ever  
blows:  
1. Unplug the soundbar power cord from the AC outlet and wait for the Power LED to  
turn off before proceeding.  
NOTE: You can connect three different source components to the three input connectors.  
See Source Connections, on page 9, for more information.  
Wireless Code switch: This switch selects among four different wireless channels for  
the wireless subwoofer signal.  
IMPORTANT: Be sure to set the soundbar’s Wireless Code switch to the same  
channel that you set the subwoofer’s Wireless Code switch. See Wireless Code  
Switches, on page 10, for more information.  
2. Use a screwdriver to open the fuse holder.  
3. Remove the blown fuse.  
4. Replace the fuse with an identical fuse: T4AL/250V (110 – 120V AC operation);  
T2AL/250V (220 – 240V AC operation).  
EQ switch: This switch adjusts the soundbar’s bass performance for either wall or  
table mounting. If you’re mounting the soundbar on a wall with the included wall-mount  
brackets, set this switch to the “Wall” position for the most natural-sounding bass  
performance. If you are placing the soundbar on a table, set the EQ switch to the “Table”  
position for the most natural-sounding bass performance.  
CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE, REPLACE THE FUSE ONLY  
WITH THE SAME TYPE AND RATING.  
Power Cord connector: Connect the supplied AC power cord here. See Power  
Connections, on page 9, for more information.  
CAUTION: Before connecting the power cord, make sure the Voltage Selector  
switch (see below) is in the correct setting for your local AC voltage. See Power  
Connections, on page 9, for more information.  
4
 
SB 30  
Connections and Controls  
Soundbar Top-Panel Controls  
Soundbar Status LEDs  
The soundbar has three LED indicators located behind the grille, as shown in the  
illustration below.  
Power  
Button  
and  
Power  
LED  
Surround  
Mode  
Button  
Volume  
Down/Up  
Buttons  
Source  
Selector  
Button  
Dolby  
Volume  
Button  
Status  
LEDs  
Power button: When the soundbar is in the Standby mode (the Power LED is amber),  
pressing the Power button will turn on the soundbar. When the soundbar is on (the Power  
LED is blue), pressing the Power button will put it into the Standby mode.  
The status LEDs light up in different colors and numbers to indicate the following:  
Active input source (white LEDs)  
1 LED = Optical Digital Input  
Power LED: The Power LED will display different colors and patterns to indicate the  
soundbar’s status:  
• Power LED is constantly blue: The soundbar is on.  
• Power LED is flashing blue: The soundbar is muted.  
• Power LED is amber: The soundbar is in the Standby mode.  
• Power LED is off: The soundbar is off.  
2 LEDs = Coaxial Digital Input  
3 LEDs = Analog Input  
Active surround mode (blue LEDs)  
1 LED = Stereo mode  
2 LEDs = Virtual surround mode  
Surround Mode button: Pressing the Surround Mode button cycles the soundbar’s audio  
output through the following three surround modes: Stereo > Virtual > HARMAN Wave >  
Stereo, etc. The active surround mode is indicated by the soundbar Status LEDs (see  
Soundbar Status, LEDs below). See Surround Modes, on page 12, for information about  
the surround modes.  
3 LEDs = Wave surround mode  
(See Surround Modes, on page 12, for information about the surround modes.)  
Room Size setting (green LEDs)  
Volume Down/Up buttons: Press the “–” button to decrease the volume; press the “+”  
1 LED = Small room  
button to increase the volume.  
2 LEDs = Medium room  
Source Selector button: Pressing the Source Selector button changes the active input  
source among the Optical Digital, Coaxial Digital and Analog input connectors. The active  
input source is indicated by the soundbar Status LEDs (see below).  
Dolby® Volume button: Pressing the Dolby Volume button cycles the Dolby Volume  
setting between off, low and high. The active setting is indicated by the soundbar Status  
LEDs (see below). See Dolby Volume, on page 13, for more information about Dolby  
Volume.  
3 LEDs = Large room  
(See Surround Modes, on page 12, for information about the Room Size setting.)  
Dolby Volume setting (red LEDs)  
1 LED = Off  
2 LEDs = Low  
3 LEDs = High  
(See Dolby Volume, on page 13, for information about Dolby Volume.)  
NOTE: The Status LEDs will turn off after five seconds of no button presses.  
5
 
SB 30  
Connections and Controls  
Subwoofer Controls  
Power LED  
(on top of unit)  
Phase  
Switch  
This area is designed to become  
quite warm during normal operation  
Volume  
Control  
DO NOT OPEN  
Wireless  
Code Switch  
Power Switch  
Power Cord  
Power LED (on top of unit): The Power LED’s color indicates the subwoofer’s operational  
status:  
Wireless Code switch: This switch selects among four different wireless channels for  
the wireless subwoofer signal.  
• Blue: The subwoofer is operational.  
• Amber: The subwoofer is in the Standby mode.  
• Off: The subwoofer is turned off.  
IMPORTANT: Be sure to set the subwoofer’s Wireless Code switch to the same  
channel that you set the soundbar’s Wireless Code switch. See Wireless Code  
Switches, on page 10, for more information.  
Power switch: Set this switch to the “On” position to activate the subwoofer. In normal  
operation, this switch will be left in the “On” position. See Turning the Subwoofer On and  
Off, on page 11, for more information.  
Phase switch: This switch determines whether the subwoofer driver’s piston-like action  
moves in and out in phase with the speakers in the soundbar. If the subwoofer were  
to play out of phase with the soundbar speakers, the sound waves from the soundbar  
could cancel out some of the sound waves from the subwoofers, reducing bass  
performance and sonic impact. This phenomenon depends in part on the placement of  
the subwoofer and soundbar relative to each other in the room. See Subwoofer Phase  
Switch, on page 11, for more information.  
Power cord (non-detachable): Plug this cord into an active, unswitched AC outlet. See  
Power Connections, on page 9, for more information.  
Volume control: Use this control to balance the subwoofer’s volume with that of  
the soundbar. Turn the knob clockwise to increase the subwoofer’s volume; turn it  
counterclockwise to decrease the subwoofer’s volume. See Subwoofer Volume Control,  
on page 11, for more information.  
6
 
SB 30  
Remote Control Functions and Placing the Soundbar and Subwoofer  
Wall-Mounting the Soundbar  
If your TV is attached to a wall, you can use the included wall-mount brackets to mount  
Remote Control Functions  
the soundbar on the wall directly below the TV screen.  
Mute  
Button  
Power  
Button  
Volume Down  
Button  
Volume Up  
Button  
Surround Mode  
Button  
Dolby Volume  
Button  
Room Size  
Button  
Source Selector  
Button  
Mute button: Press this button to mute the system (the soundbar Power LED will flash  
blue); press again to unmute the system.  
Power button: When the soundbar is in the Standby mode (the soundbar Power LED is  
amber), pressing the Power button will turn on the soundbar. When the soundbar is on  
(the Power LED is blue), pressing the Power button will put it into the Standby mode.  
Volume Down/Up buttons: Press the “–” button to decrease the volume; Press the “+”  
button to increase the volume.  
1. Determine the location for the soundbar on the wall. Make sure that the top of the  
soundbar will not block your view of the TV screen when it is mounted on the wall.  
Surround Mode button: Pressing the Surround Mode button cycles the soundbar’s audio  
output through the following three surround modes: Stereo > Virtual > HARMAN Wave >  
Stereo, etc. The active surround mode is indicated by the soundbar Status LEDs (see  
Soundbar Status LEDs, on page 5). See Surround Modes, on page 12, for information  
about the surround modes.  
2. Mark the locations of the soundbar wall-mount bracket holes on the wall. The holes  
for the left and right brackets are spaced 830mm apart and are designed to accept  
#8 screws. The top and bottom holes for each bracket are spaced 25mm apart. See  
the illustration below.  
Dolby® Volume button: Pressing the Dolby Volume button cycles the Dolby Volume  
setting among Off, Low and High. The active setting is indicated by the status LEDs (see  
Soundbar Status LEDs, on page 5). See Dolby Volume, on page 13, for more information  
about Dolby Volume.  
25mm  
830mm  
Room Size button: The Room Size button lets you tailor the soundbar’s energy field in  
the HARMAN Wave surround mode to match the size of your listening room. See Surround  
Modes: HARMAN Wave, on page 12, for more information.  
NOTE: To ensure that the soundbar will be level, use a carpenter’s level, laser sight or  
other device to ensure that the two sets of holes are at exactly the same height.  
Source Selector button: Pressing the Source Selector button changes the active input  
source among the Optical Digital, Coaxial Digital and Analog input connectors. The active  
input source is indicated by the status LEDs (see Soundbar Status LEDs, on page 5).  
3. Attach the two wall-mount brackets to the wall at the locations you marked, using  
hardware that is appropriate for the wall’s construction and materials. Note that  
the soundbar weighs 8.4 lb (3.8kg). Be sure to use hardware that can support this  
weight.  
Place the Soundbar and Subwoofer  
Placing the Soundbar on a Table  
If your TV is placed on a table, you can place the soundbar on the table directly in front of  
the TV stand, centered with the TV screen.Attach the supplied rubber feet to the soundbar  
as shown in the illustration and set the soundbar’s EQ switch in the “Table” position.  
4. Set the soundbar’s EQ switch in the “Wall” position.  
As long as the table’s surface is flat, the soundbar will rest on the rubber feet.  
7
 
Placing the Soundbar and Subwoofer  
and Connecting the System  
SB 30  
5. After making all of the connections described in Connecting the System, on this  
page, attach the soundbar to the brackets by sliding the slots in its feet onto the  
brackets’ vertical tabs.  
Connecting the System  
Source Connections  
Analog: Use the supplied stereo audio cable to connect the soundbar’s Analog Input  
connectors to your TV’s stereo audio output. If your TV has two sets of audio output  
jacks, use the set that has a fixed (not variable) output level. It will let you turn your  
TV’s speakers all the way off while the TV still supplies a constant audio signal to the  
soundbar.  
Digital: If your disc player, cable tuner or satellite tuner has a coaxial or optical digital  
output, you can use the supplied optical digital audio cable and a coaxial digital audio  
cable (not supplied) to connect them to the soundbar’s Optical and Coaxial Digital Input  
connectors. We recommend setting the component’s digital output to “Bitstream” so it  
will send Dolby® Digital and DTS® bitstreams to the SB 30 CNTR for decoding. This will  
produce better results when using the Virtual and HARMAN Wave surround modes (see  
Surround Modes, on page 11).  
NOTE: If your disc player, cable tuner or satellite tuner does not have a digital output you  
can connect its analog audio output to your TV. The TV will send its audio signal to the  
soundbar through the analog connection described above.  
Placing the Subwoofer  
The performance of a subwoofer is directly related to its placement in the listening room  
and its physical position relative to the other speakers in the system.  
TV  
While it is true that in general our ears do not hear directional sounds at the low  
frequencies where subwoofers operate, when installing a subwoofer within the limited  
confines of a room, the reflections, standing waves and absorptions generated within the  
room will strongly influence the performance of any subwoofer system. As a result, the  
specific location of the subwoofer in the room does become important to the amount and  
quality of bass that is produced.  
AUDIO  
OUT  
Stereo  
Audio Cable  
(supplied)  
For example, placing the subwoofer next to a wall generally will increase the amount of  
bass in the room; placing it in a corner (1) generally will maximize amount of bass in the  
room. However, corner placement can also increase the destructive effect of standing  
waves on bass performance. This effect can vary depending on the listening position –  
some listening positions may yield very good results while others may have far too much  
(or too little) bass at certain frequencies.  
Input  
Input  
L
1
2
3
4
In many rooms, placing the subwoofer along a wall away from a corner (2) can produce  
the best integration between the sound of the subwoofer and that of the left and right  
speakers. In some rooms, the best performance could even result from placing the  
subwoofer behind the listening position (3).  
SB 30 CNTR Soundbar  
Input  
Input  
L
1
2
3
4
Optical  
Digital Audio Cable  
(supplied)  
OPTICAL  
DIGITAL  
OUT  
Satellite Tuner  
Disc Player  
TV  
1.  
Coaxial  
Digital Audio Cable  
(not supplied)  
SB 30 CNTR  
2.  
Soundbar  
COAXIAL  
DIGITAL  
OUT  
Voltage Selector Switch  
The soundbar’s Voltage Selector switch is set at the factory to accommodate the AC  
power voltage in the area where the soundbar is shipped.  
IMPORTANT: Before you connect the power cord for the first time it is a good idea  
to verify that the setting of the voltage selector is appropriate for the power in  
your area.  
In the event that you do need to change the Voltage Selector switch setting:  
6. Make sure that the soundbar is powered off and the power cord is disconnected  
from the soundbar.  
3.  
7. Slide the Voltage Selector switch to the appropriate setting (“110 – 120V” or “220 –  
240V”) as required for your area.  
We strongly recommend that you experiment with placement before choosing a final  
location for your subwoofer. One way you can determine the best location for the  
subwoofer is by temporarily placing it in the listening position and playing music with  
strong bass content. Move around to various locations in the room while the system is  
playing (putting your ears where the subwoofer would be placed), and listen until you find  
the location where the bass performance is best. Place the subwoofer in that location.  
WARNING: DO NOT UNDER ANY CIRCUMSTANCES OPERATE THE SOUNDBAR WITH  
THE WRONG VOLTAGE SELECTED. DOING SO MAY RESULT IN SERIOUS DAMAGE TO  
THE SOUNDBAR, WHICH WILL NOT BE COVERED BY WARRANTY.  
8
 
Connecting and Using  
Your Soundbar Speaker System  
SB 30  
Power Connections  
After you have made and verified all of the source connections and the Voltage Selector  
switch setting:  
1. Connect the supplied AC power cord to the SB 30 CNTR’s Power Cord connector and  
to a working unswitched wall outlet.  
Using Your Soundbar Speaker System  
Set the soundbar’s and subwoofer’s Power switches in their “On” positions. Normally, you  
can leave both Power switches set to “On” all the time. If you will be away from home for  
an extended period of time, or if you will not be using the system for an extended period,  
set both Power switches to “Off.”  
2. Connect the subwoofer’s power cord into a working unswitched wall outlet.  
SB 30 CNTR Soundbar  
SB 30 CNTR Soundbar  
Input  
Input  
Input  
Input  
L
L
1
2
3
4
1
2
3
4
AC  
Power Cord  
(supplied)  
Power Cord Voltage Selector  
Connector Switch  
Power  
Switch  
SB 30 Subwoofer  
This area is designed to become  
quite warm during normal operation  
Wall  
Outlet  
L
SB 30 Subwoofer  
Power  
Switch  
This area is designed to become  
quite warm during normal operation  
Power  
Cord  
Wall  
Outlet  
9
 
SB 30  
Using Your Soundbar Speaker System  
Wireless Code Switches  
Turning the Soundbar On and Off  
In the unlikely event that you encounter interference when operating the system, or if you  
have more than one SB 30 system in operation, you may change the channel at which  
the wireless system operates. There are four-position Wireless Code switches on both  
the soundbar and subwoofer. To change the wireless channel, set each of the switches  
to one of the other three positions. IMPORTANT: The switches on the soundbar and  
the subwoofer must be set to the same position for the wireless system to work.  
Manually: To turn the soundbar on manually, momentarily press the Power button on the  
soundbar or on the remote control. Pressing the Power button while the soundbar is on  
will put it into the Standby mode.  
Power  
Button  
Power  
Button  
SB 30 CNTR Soundbar  
Input  
Input  
L
1
2
3
4
NOTE: If you put the soundbar into the Standby mode manually, you can turn it back on  
only by manually pressing the Power button again.  
Input  
Input  
Auto turn-on: The soundbar has a signal detector that will automatically turn the unit on  
when it senses an audio signal at any of its inputs. To minimize power consumption, the  
signal detector is not activated unless the soundbar first senses any kind of IR remote  
signal. Once the soundbar’s signal detector has been activated, the unit will automatically  
turn from Standby to on as soon as it detects an input signal at any of its source input  
connections.  
L
1 2 3 4  
Auto turn-off: The soundbar will automatically enter the Standby mode if no audio signal  
is detected at any of its source input connections for approximately 15 minutes.  
Wireless Code  
Switch  
Turning the Subwoofer On and Off  
The subwoofer will automatically turn on when it receives an audio signal from the  
soundbar, and it will return to the Standby mode when it has received no audio signal for  
15 minutes. The subwoofer’s Power LED will turn blue when the subwoofer is on and will  
turn amber when the subwoofer is in Standby.  
Set Both Switches  
to the Same Number  
Subwoofer Volume Control  
Use the subwoofer’s Volume control to balance its volume with that of the soundbar. Once  
you find the proper balance between the subwoofer and the soundbar, the soundbar’s  
Volume Up/Down buttons will control the volume of the entire system, and you should not  
have to readjust the subwoofer’s Volume control.  
This area is designed to become  
quite warm during normal operation  
L
Wireless Code  
Switch  
This area is designed to become  
quite warm during normal operation  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
SB 30 Subwoofer  
Volume  
Control  
Notes on setting subwoofer volume  
• Sometimes the ideal subwoofer volume setting for music is too loud for films,  
while the ideal setting for films is too quiet for music. When setting the subwoofer’s  
Volume control, listen to both music and films with strong bass content and find a  
“middle ground” volume level that works for both.  
• If your subwoofer always seems too loud or too quiet, you may want to place it in  
a different location. Placing the subwoofer in a corner will always tend to increase  
its bass output, while placing it away from any walls or corners will always tend to  
lessen its bass output.  
10  
 
SB 30  
Using Your Soundbar Speaker System  
Subwoofer Phase Switch  
Selecting an Input Source  
When the subwoofer is properly in phase with the soundbar speakers, the sound will be  
clearer and have more impact. In-phase performance will make percussive sounds like  
drums, piano and plucked strings sound more lifelike. Although there is no absolutely  
correct setting for the subwoofer’s Phase switch, in most cases it should be left in the  
“Normal” position. The best way to set the Phase switch is to listen to music that you  
are familiar with and adjust the switch so that drums and other percussive sounds have  
maximum impact.  
Press the Source button on the soundbar or the remote control to switch among the three  
sources: optical digital, coaxial digital and analog.  
Source  
Button  
Source  
Button  
This area is designed to become  
quite warm during normal operation  
RISK OF ELETIC SOK  
The soundbar’s Status LEDs will glow white to indicate the active source.  
Optical Digital  
Coaxial Digital  
Analog  
Phase  
Switch  
Surround Modes  
Your soundbar incorporates extremely sophisticated digital signal processing that,  
along with 13 individual transducers powered by 11 amplifier channels, creates an  
astonishingly realistic surround-sound presentation in any size room, for listeners at any  
position in the room, without needing any extra speakers or wires.  
Adjusting the System’s Volume  
Press the Volume Up and Down buttons on the soundbar or the remote control to raise  
and lower the system’s volume one step at a time. Hold down the buttons to raise or lower  
the volume continuously. To mute the system, press the remote control’s Mute button.  
Press the Surround Mode button on the soundbar or the remote control to switch among  
the three surround modes: Stereo, Virtual and HARMAN Wave.  
Volume Down/Up  
Buttons  
Mute Button  
Surround Mode  
Button  
Volume Down/Up  
Buttons  
Surround Mode  
Button  
For the best sound, we recommend turning your TV’s built-in speakers off. Consult your  
TV’s owner’s manual to find out how to do it. If there is no way to turn your TV’s speakers  
off, you can adjust your TV’s volume so that the SB 30 system will always supply most  
of the sound:  
The soundbar’s Status LEDs glow blue to indicate the active surround mode:  
Stereo  
1. Using the volume buttons on your TV, turn its volume all the way down.  
2. Then use the soundbar’s Volume Up/Down buttons to set the sound to a comfortable  
listening level.  
Virtual  
HARMAN Wave  
11  
 
SB 30  
Using Your Soundbar Speaker System  
Stereo: The Stereo mode reproduces the input signal in conventional two-channel stereo,  
utilizing the soundbar’s left and right speakers. Digital equalization and digital crossover  
filters help achieve accurate performance for listeners in a variety of seating positions,  
not just those directly on the speaker’s center line.  
Dolby Volume  
Your soundbar implements Dolby Volume processing, which can improve the audio  
performance of the system by revealing subtle details in the sound, even at normal  
home-listening volumes.  
One concern of the typical home theater listener is that volumes can vary widely for  
different programs played by a source (e.g., television commercial advertisements are  
often much louder than the main program). Another is that details heard in the recording  
studio at typically high reference volumes are lost at the lower volumes used by many  
listeners at home.  
Stereo Mode  
The soundbar uses two Dolby Volume techniques to address these issues. The Leveler  
module maintains a consistent listening volume within a source (e.g., commercial  
television or different tracks on a mix CD). The Modeler module endeavors to re-create  
the reference presentation that was heard in the recording studio without losing portions  
of the program at the typically lower volume levels often used in the home. When the  
Modeler module is active, you may notice details of the performance that were hidden  
when the program was played on other equipment.  
Virtual: The Virtual mode utilizes sophisticated digital signal processing and an additional  
four transducers to simulate the reflected sounds that would be created by the rear-  
channel speakers in a room with a dedicated surround-sound system. The soundbar’s  
digital signal processing is specifically designed to maximize the useful listening area  
while reducing sonic colorations.This digital processing also enhances conventional stereo  
and MP3 sources by creating rear ambience that adds depth to the sound presentation.  
Press the Dolby Volume button on the remote to adjust the Dolby Volume setting.  
Virtual Mode  
Dolby Volume  
Button  
This mode achieves the best surround sound effect for listeners who are sitting along the  
soundbar’s center line, from 3 ft – 10 ft (1m – 3m) away from the speaker.  
HARMAN Wave: The HARMAN Wave mode utilizes all 13 of the soundbar’s transducers  
to create both left and right surround sound fields, in addition to using the left and  
right transducer groups to reproduce the front left and right stereo signals. Extremely  
sophisticated digital signal processing uses wave field synthesis to separately control  
direct and indirect sound fields, creating an impressive surround sound sensation in even  
a large room and for many listeners seated over a large listening area.  
The soundbar’s Status LEDs glow red to indicate the active Dolby Volume setting:  
Dolby Volume Off  
HARMAN Wave Mode  
Dolby Volume Low  
Dolby Volume High  
Off: No Dolby Volume processing.  
The HARMAN Wave mode features a Room Size adjustment that allows you to tailor the  
soundbar’s energy field to match the size of your listening room. Press the Room Size  
button on the remote  
Low: Dolby Volume Modeler module is active.  
High: Dolby Volume Modeler and Leveler modules are active.  
Room Size  
Button  
The soundbar’s Status LEDs glow green to indicate the active Room Size setting:  
Small Room  
Medium Room  
Large Room  
Feel free to experiment with this adjustment to find the effect that works best for your  
particular listening room and seating arrangement.  
As with the Virtual mode, in the HARMAN Wave mode the soundbar’s digital signal  
processing also creates rear ambience that adds depth to the sound presentation for  
conventional stereo and MP3 sources.  
12  
 
SB 30  
Specifications  
Specifications  
SB 30 System  
Frequency response:  
40Hz – 20kHz  
SB 30 CNTR Soundbar  
Low-frequency transducers:  
High-frequency transducers:  
Amplifier power:  
Six x 2" (51mm) cones  
Seven x 1" (25mm) domes  
40 watts x 4; 10 watts x 7  
Power requirement:  
110V – 120V AC, 60Hz (USA);  
220V – 240V AC, 50Hz (EU), selectable  
Power consumption :  
<0.5W (standby); 230W (maximum)  
Dimensions (H x W x D):  
3-15/16" x 45-11/16" x 3-1/8"  
(100mm x 1160mm x 80mm)  
Weight:  
8.4 lb (3.8kg)  
SB 30 Subwoofer  
Low-frequency transducer:  
Amplifier power:  
Frequency response:  
Controls:  
8" (200mm) down-firing cone  
100 watts  
40Hz – 160Hz  
Volume, phase  
Sealed  
Enclosure type:  
Power requirement:  
120V, 60Hz (USA);  
230V, 50Hz/60Hz (EU)  
Power consumption:  
<0.5W (standby); 100W (maximum)  
Dimensions (H x W x D):  
13-29/32" x 10-1/2" x 10-1/2";  
(353mm x 267mm x 267mm)  
Weight:  
19.2 lb (8.7kg)  
13  
 
SB 30  
Troubleshooting  
Troubleshooting  
If your SB 30 system isn’t performing the way you think it should, check to see if the problem is covered in this section before calling your dealer or contacting a Harman Kardon  
representative.  
Problem  
Solution  
The soundbar does not turn on (the Power LED is off):  
• Check that the soundbar’s power cord is plugged into a working AC outlet.  
• Check that the soundbar’s Power switch is in the “On” position.  
• Check if the soundbar’s AC fuse has blown. See Soundbar Rear-Panel Controls  
and Connections: AC Fuse Holder, on page 4, for instructions on checking and  
changing the fuse.  
• Check if the soundbar’s voltage selector switch is set in the incorrect position for  
the AC voltage in your area. CAUTION: If the switch is set in the incorrect position,  
do not change the switch position or attempt to turn the soundbar back on.  
Unplug the soundbar from the wall outlet and take it to an authorized Harman  
Kardon service center.  
The subwoofer does not turn on (the Power LED is off):  
• Check that the subwoofer’s power cord is plugged into a working AC outlet.  
• Check that the subwoofer’s Power switch is in the “On” position.  
There is no sound coming from both the soundbar and the subwoofer  
(their Power LEDs are amber or blue):  
• Check that the soundbar is on (the Power LED is blue).  
• Check that the cable connecting the TV or other source component to the soundbar  
is properly connected at both ends.  
• Check that the soundbar is set to the correct input source (one white Status LED  
glows for optical digital, two white Status LEDs for coaxial digital, and three white  
Status LEDs for analog) and that the input source device is playing an audio signal.  
• Check that the system is not muted (when the system is muted, the soundbar’s  
Power LED flashes blue). If the system is muted, press the remote control’s Mute  
button to un-mute the system.  
• Check that the soundbar’s volume is not turned all the way down.  
There is no sound coming from just the subwoofer (the Power LED is amber or blue):  
• Check that the Subwoofer Volume control is not turned all the way down (fully  
counterclockwise).  
• Check that the Wireless Code switches on the subwoofer and soundbar are both  
set to the same setting number.  
• Move the subwoofer closer to the soundbar. The maximum wireless operation  
distance is 50 feet (15.3m).  
The soundbar’s sound is distorted:  
• Check the source device to see if the distortion is coming from it and not from  
the soundbar.  
The system’s sound is too quiet, even when the soundbar’s volume is turned all  
the way up:  
• If the TV or source component is connected via a variable analog output, check its  
instructions to be sure that the output is not turned down too low.  
The bass output is not loud enough:  
• Turn up the subwoofer’s Volume control.  
• Move the subwoofer into a corner of the room.  
• Move the subwoofer closer to the seating location.  
14  
 
HARMAN Consumer, Inc.  
8500 Balboa Boulevard, Northridge, CA 91329 USA  
© 2011 HARMAN International Industries, Incorporated. All rights reserved.  
Harman Kardon is a trademark of HARMAN International Industries, Incorporated, registered in the United States and/or other countries.  
Manufactured under license from Dolby Laboratories. Dolby, Pro Logic and the double-D symbol are registered trademarks of Dolby  
Laboratories. MLP Lossless is a trademark of Dolby Laboratories.  
Manufactured under license under U.S. Patent Nos: 5,956,674; 5,974,380; 6,487,535 & other U.S. and worldwide patents issued &  
pending. DTS, the Symbol, & DTS and the Symbol together are registered trademarks & DTS Digital surround and the DTS logos are  
trademarks of DTS, Inc. Product includes software. © DTS, Inc. All Rights Reserved.  
Features, specifications and appearance are subject to change without notice.  
Part No. 950-0357-001  
 

Graco High Chair PD223741A User Manual
Grizzly Sander H7671 User Manual
Gyration Mouse Ultra Cordless Optical Mouse User Manual
Honeywell Home Security System GEC User Manual
HP Hewlett Packard Portable Media Storage AP836B User Manual
HTC Cell Phone ATHE100 User Manual
Hunter Fan Dehumidifier 41554 01 User Manual
IBM Network Card 3301690 User Manual
IBM Network Card EM78P259N 260N User Manual
Impex Fitness Equipment SB 228 User Manual