Harbor Freight Tools Work Light 66308 User Manual

led work light  
66308  
Set up And operAting inStructionS  
®
distributed exclusively by harbor Freight tools .  
3491 Mission Oaks Blvd., Camarillo, CA 93011  
Visit our website at: http://www.harborfreight.com  
read this material before using this product.  
Failure to do so can result in serious injury.  
SAVe thiS mAnuAl.  
©
®
Copyright 2008 by Harbor Freight Tools . All rights reserved. No portion of this manual or any  
artwork contained herein may be reproduced in any shape or form without the express written  
consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally.  
Due to continuing improvements, actual product may differ slightly from the product described  
herein. Tools required for assembly and service may not be included.  
For technical questions or replacement parts, please call 1-800-444-3353.  
 
Many accidents are caused by  
poorly maintained items.  
nia Health & Safety Code § 25249.5,  
et seq.)  
5. Service  
6. The warnings, precautions, and  
instructions discussed in this instruc-  
tion manual cannot cover all possible  
conditions and situations that may  
occur. It must be understood by the  
operator that common sense and cau-  
tion are factors which cannot be built  
into this product, but must be supplied  
by the operator.  
a. have the light serviced by a  
qualified repair person using  
only identical replacement parts.  
This will ensure that the safety of  
the Light is maintained.  
light Safety warnings  
1. Maintain labels and nameplates on  
the Light. These carry important  
safety information. If unreadable or  
missing, contact Harbor Freight Tools  
for a replacement.  
SAVe theSe  
inStructionS.  
grounding  
2. Do not leave the Light unattended  
when it is plugged into an electrical  
outlet. Turn off the Light, and unplug  
it from its electrical outlet before leav-  
ing.  
improperly  
connecting the  
grounding wire can result in  
electric shock.  
Check with a qualified  
3. This product is not a toy. Keep it out  
of reach of children.  
electrician if you are in doubt  
as to whether the outlet is  
properly grounded. do not  
modify the power cord plug  
provided with the tool. never  
remove the grounding prong  
from the plug. do not use the  
tool if the power cord or plug  
is damaged. if damaged, have  
it repaired by a service facility  
before use. if the plug will not  
fit the outlet, have a proper  
outlet installed by a qualified  
electrician.  
4. People with pacemakers should  
consult their physician(s) before use.  
Electromagnetic fields in close prox-  
imity to heart pacemaker could cause  
pacemaker interference or pacemaker  
failure. In addition, people with pace-  
makers should:  
• Avoid operating alone.  
• Properly maintain and inspect to  
avoid electrical shock.  
• Any power cord must be prop-  
erly grounded. Ground Fault Circuit  
Interrupter (GFCI) should also be  
implemented – it prevents sustained  
electrical shock.  
5. WARNING: Handling the cord on  
this product will expose you to lead,  
a chemical known to the State of  
California to cause cancer, and birth  
defects or other reproductive harm.  
Wash hands after handling. (Califor-  
SKU 66308  
For technical questions, please call 1-800-444-3353.  
Page 3  
 
preceding illustration. (See 3-prong  
plug and outlet.)  
grounded tools:  
tools with three prong plugs  
double insulated tools:  
tools with two prong plugs  
1. Tools marked with “Grounding Re-  
quired” have a three wire cord and  
three prong grounding plug. The  
plug must be connected to a properly  
grounded outlet. If the tool should  
electrically malfunction or break down,  
grounding provides a low resistance  
path to carry electricity away from  
the user, reducing the risk of elec-  
tric shock. (See 3-prong plug and  
outlet.)  
1. Tools marked “Double Insulated” do  
not require grounding. They have  
a special double insulation system  
which satisfies OSHA requirements  
and complies with the applicable stan-  
dards of Underwriters Laboratories,  
Inc., the Canadian Standard Associa-  
tion, and the National Electrical Code.  
(See outlets for 2-prong plug.)  
2. The grounding prong in the plug is  
connected through the green wire in-  
side the cord to the grounding system  
in the tool. The green wire in the cord  
must be the only wire connected to  
the tool’s grounding system and must  
never be attached to an electrically  
“live” terminal. (See 3-prong plug  
and outlet.)  
2. Double insulated tools may be used  
in either of the 120 volt outlets shown  
in the preceding illustration. (See  
outlets for 2-prong plug.)  
extension cords  
1. Grounded tools require a three wire  
extension cord. Double Insulated  
tools can use either a two or three  
wire extension cord.  
3. The tool must be plugged into an  
appropriate outlet, properly installed  
and grounded in accordance with all  
codes and ordinances. The plug and  
outlet should look like those in the  
2. As the distance from the supply outlet  
increases, you must use a heavier  
gauge extension cord. Using exten-  
sion cords with inadequately sized  
wire causes a serious drop in voltage,  
resulting in loss of power and possible  
tool damage. (See table A.)  
3. The smaller the gauge number of the  
wire, the greater the capacity of the  
cord. For example, a 14 gauge cord  
SKU 66308  
For technical questions, please call 1-800-444-3353.  
Page 4  
 
can carry a higher current than a 16  
gauge cord. (See table A.)  
Symbology  
4. When using more than one exten-  
sion cord to make up the total length,  
make sure each cord contains at least  
the minimum wire size required. (See  
table A.)  
Double Insulated  
Canadian Standards  
Association  
Underwriters Laboratories, Inc.  
Volts Alternating Current  
Amperes  
5. If you are using one extension cord  
for more than one tool, add the name-  
plate amperes and use the sum to  
determine the required minimum cord  
size. (See table A.)  
V~  
A
No Load Revolutions per  
Minute (RPM)  
n xxxx/min.  
0
6. If you are using an extension cord  
outdoors, make sure it is marked with  
the suffix “W-A” (“W” in Canada) to  
indicate it is acceptable for outdoor  
use.  
7. Make sure the extension cord is  
properly wired and in good electrical  
condition. Always replace a damaged  
extension cord or have it repaired by  
a qualified electrician before using it.  
8. Protect the extension cords from  
sharp objects, excessive heat, and  
damp or wet areas.  
recommended minimum wire  
gAuge For eXtenSion cordS*  
(120/240 VOLT)  
eXtenSion cord  
nAmeplAte  
AmpereS  
length  
(at full load)  
0 – 2.0  
2.1 – 3.4  
3.5 – 5.0  
18  
18  
18  
18  
18  
14  
12  
18  
18  
18  
16  
14  
12  
10  
18  
18  
16  
14  
12  
10  
-
18  
16  
14  
12  
10  
-
16  
14  
12  
12  
-
5.1 – 7.0  
7.1 – 12.0  
12.1 – 16.0  
16.1 – 20.0  
-
-
-
* Based on limiting the line  
voltage drop to five volts at  
150% of the rated amperes.  
tABle A  
SKU 66308  
For technical questions, please call 1-800-444-3353.  
Page 5  
 
SpeciFicAtionS  
operAting inStructionS  
read the entire importAnt  
SAFetY inFormAtion  
Electrical Requirements 110 V~ / 60 Hz / 4.4 W  
Light Strength  
270 Lumens  
section at the beginning of this  
manual including all text under  
subheadings therein before set  
up or use of this product.  
unpAcking  
When unpacking, make sure that  
the item is intact and undamaged. If any  
parts are missing or broken, please call  
Harbor Freight Tools at the number shown  
on the cover of this manual as soon as  
possible.  
1. Position the LED work light near the  
work. Loosen Knob (3) and adjust  
Lamp Assembly (1) to direct the light  
beam. Tighten the Knob (3).  
2. Plug the Light into a grounded 110V  
electrical outlet.  
initiAl Set up  
inStructionS  
3. To prevent accidents, disconnect the  
power supply after use. Clean, then  
store the tool indoors out of children’s  
reach.  
read the entire importAnt  
SAFetY inFormAtion  
section at the beginning of this  
manual including all text under  
subheadings therein before set  
up or use of this product.  
to preVent  
SeriouS injurY  
From AccidentAl  
operAtion:  
unplug the light from the  
electrical outlet before  
assembly.  
Note: For additional information regarding  
the parts listed in the following pages,  
refer to the Assembly Diagram near  
the end of this manual.  
1. Slide the Base (2) into the bottom of  
the Lamp Assembly (1).  
2. Secure with the Knob (3).  
reV 09b  
SKU 66308  
For technical questions, please call 1-800-444-3353.  
Page 6  
 
uSer-mAintenAnce  
pArtS liSt  
inStructionS  
part  
description  
Qty  
1
1
Procedures not specifically  
explained in this manual must  
be performed only by a qualified  
technician.  
1
2
3
Lamp Assembly  
Base  
Knob  
1
ASSemBlY diAgrAm  
to preVent  
SeriouS injurY  
From AccidentAl  
operAtion:  
unplug the light from its  
electrical outlet before  
performing any inspection,  
maintenance, or cleaning  
procedures.  
1
to preVent SeriouS  
injurY From tool  
FAilure:  
do not use damaged  
equipment. if abnormal noise  
or vibration occurs, have the  
problem corrected before  
further use.  
cleaning, maintenance, and  
lubrication  
3
2
1. BeFore eAch uSe, inspect the  
general condition of the tool. Check  
for loose screws, misalignment or  
binding of moving parts, cracked or  
broken parts, damaged electrical wir-  
ing, and any other condition that may  
affect its safe operation.  
record product’s Serial number  
here:  
Note: If product has no serial number,  
record month and year of purchase  
instead.  
2. AFter uSe, clean external surfaces  
of the tool with clean, moist cloth.  
3.  
wArning! if the supply cord of  
this power tool is damaged, it must  
be replaced only by a qualified  
service technician.  
Note: No replacement parts.  
SKU 66308  
For technical questions, please call 1-800-444-3353.  
Page 7  
 
limited 90 dAY wArrAntY  
Harbor Freight Tools Co. makes every effort to assure that its products meet  
high quality and durability standards, and warrants to the original purchaser that this  
product is free from defects in materials and workmanship for the period of 90 days  
from the date of purchase. This warranty does not apply to damage due directly or  
indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside  
our facilities, criminal activity, improper installation, normal wear and tear, or to lack of  
maintenance. We shall in no event be liable for death, injuries to persons or property,  
or for incidental, contingent, special or consequential damages arising from the use of  
our product. Some states do not allow the exclusion or limitation of incidental or con-  
sequential damages, so the above limitation of exclusion may not apply to you. THIS  
WARRANTy IS ExPRESSLy IN LIEU OF ALL OTHER WARRANTIES, ExPRESS OR  
IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITy AND FITNESS.  
To take advantage of this warranty, the product or part must be returned to us  
with transportation charges prepaid. Proof of purchase date and an explanation of the  
complaint must accompany the merchandise. If our inspection verifies the defect, we  
will either repair or replace the product at our election or we may elect to refund the  
purchase price if we cannot readily and quickly provide you with a replacement. We will  
return repaired products at our expense, but if we determine there is no defect, or that  
the defect resulted from causes not within the scope of our warranty, then you must  
bear the cost of returning the product.  
This warranty gives you specific legal rights and you may also have other rights  
which vary from state to state.  
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353  
SKU 66308  
For technical questions, please call 1-800-444-3353.  
Page 8  
 

Graco Baby Playpen PD114224C User Manual
Hans Grohe Plumbing Product 97523000 User Manual
Hasbro Games 08628 User Manual
Havis Shields Window WGI F13 User Manual
Hotpoint Washer Dryer WDPG 9640 User Manual
HP Hewlett Packard Fax Machine 820 RF User Manual
HP Hewlett Packard Personal Computer A1630n User Manual
Hunter Fan Home Safety Product 45180 User Manual
Hunter Fan Thermostat 43057 User Manual
Hypertec Carrying Case 2110V2 User Manual