Harbor Freight Tools Garage Door Opener 96326 User Manual

garage door  
threshold  
Model 96326 - 8’  
Model 96327 - 10’  
Model 96328 - 16’  
installation instructions  
Adhesive shown is not included.  
Diagrams within this manual may not be drawn proportionally.  
Due to continuing improvements, actual product may differ slightly from the product described herein.  
®
distributed exclusively by harbor Freight tools .  
3491 Mission Oaks Blvd., Camarillo, CA 93011  
Visit our website at: http://www.harborfreight.com  
read this material before using this product.  
Failure to do so can result in serious injury.  
saVe this Manual.  
©
®
Copyright 2007 by Harbor Freight Tools . All rights reserved. No portion of this  
manual or any artwork contained herein may be reproduced in any shape or form  
without the express written consent of Harbor Freight Tools.  
For technical questions or replacement parts, please call 1-800-444-3353.  
 
unpacking  
When unpacking, check to make sure that the item is intact and undamaged. If  
any parts are missing or broken, please call Harbor Freight Tools at the number shown  
on the cover of this manual as soon as possible.  
asseMbly  
There is no assembly required for this Garage Threshold.  
installation instructions  
read the entire iMportant saFety inForMation section at the  
beginning of this manual including all text under subheadings therein  
before set up or use of this product.  
Fitting and installing the threshold  
1.  
2.  
Open the garage door and clean the bottom of the door and the area of the  
garage floor where the door and the floor meet. Make sure there is no moisture  
or dirt on the surface or you will not get a good bond with the Threshold.  
Place the Threshold in the opening, centering it between the door tracks on  
each side of the entrance. The garage door tracks are the channels the door  
uses as it rolls up and down. The Threshold is made to fit most garage doors so  
usually no trimming is necessary. If you do have to trim, use a straight edge for a  
uniform fit when the Threshold is installed.  
Figure 1  
Garage Door (Down)  
45° Angle  
Garage Door Threshold  
3.  
4.  
Lower the door onto the Threshold. Place the 45° angle of the Threshold against  
the inside of the bottom of the door. The 45° angle of the Threshold should be  
against the inside of the door for a proper seal against moisture.  
Trace the inside edge of the Threshold then raise the garage door and, using a  
carpenters pencil (not included), trace the leading edge of the Threshold.  
96526/27/28  
For technical questions, please call 1-800-444-3353.  
Page 3  
 
5.  
With the garage door still in the raised position remove the Threshold. Apply two  
1/4” rows of adhesive (not included) between the two lines running parallel the  
length of the garage door opening. Apply the adhesive lines 3/4” from the front  
and back edge of the Threshold.  
6.  
7.  
Using the adhesive (not included) make a zig-zag line from the front adhesive  
line to the back adhesive line and run this zig-zag line the entire length of the two  
lines.  
Follow the adhesive (not included) label directions for proper dry time before  
applying the Threshold. Always keep adhesives away from children.  
8.  
9.  
Place the Threshold between the two pencil lines and carefully press into place.  
Lower the Garage door so it may act as a clamp holding the Threshold until the  
adhesive drys. Make sure the Threshold is still alligned between the pencil lines.  
10.  
Wipe up any excess adhesive with warm water before it has a chance to harden.  
Maintenance and serVicing  
Damaged products can fail. Do not use this Threshold if it is damaged in any  
way. Have any problem corrected before use.  
cleaning and Maintenance  
1.  
2.  
periodically inspect the general condition of the Garage Door Threshold. Check  
cracks or any abnormal condition that may affect its safe operation.  
periodically clean with sponge mop. This will keep dirt from wearing down the  
surface reducing the possibility of moisture or insects entering your garage.  
please read the FolloWing careFully  
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLy DIAGRAM IN THIS MANUAL  
AS A REFERENCE TOOL ONLy. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANy REPRESENTATION OR  
WARRANTy OF ANy KIND TO THE BUyER THAT HE OR SHE IS qUALIFIED TO MAKE ANy REPAIRS TO THE PRODUCT,  
OR THAT HE OR SHE IS qUALIFIED TO REPLACE ANy PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/  
OR DISTRIBUTOR ExPRESSLy STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN By  
CERTIFIED AND LICENSED TECHNICIANS, AND NOT By THE BUyER. THE BUyER ASSUMES ALL RISK AND LIABILITy  
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING  
OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.  
parts list  
1.  
2.  
3.  
One piece Garage Threshold: Model 96326 - 8’ x 4”  
One piece Garage Threshold: Model 96327 - 10’ x 4”  
One piece Garage Threshold: Model 96328 - 16’ x 4”  
NOTE: Each package contains one piece of that model number.  
96526/27/28  
For technical questions, please call 1-800-444-3353.  
Page 4  
 

Graco Baby Accessories PD204226B User Manual
Graham Field Thermometer 1858 User Manual
Grizzly Saw G1011Z User Manual
Grundig MP3 Player MPixx 2001 User Manual
Harman Kardon Home Theater System SB15 230 User Manual
Healthrider Home Gym HREL09984 User Manual
Honeywell Ventilation Hood V4297S User Manual
Husky Dehumidifier BDH 550 User Manual
Husqvarna Lawn Mower Accessory 966659501 User Manual
Hypertec Carrying Case N18778PHY User Manual