1/2" REVERSIBLE AIR DRILL
98896
SEt up AnD OpERAtIng InStRuctIOnS
`
®
Distributed exclusively by Harbor Freight tools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE tHIS mAnuAL.
©
®
Copyright 2008 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
nOtIcE is used to
address practices
not related to personal injury.
SAVE tHIS mAnuAL
Keep this manual for the safety
warnings and precautions, assembly,
operating, inspection, maintenance and
cleaning procedures. Write the product’s
serial number in the back of the manual
near the assembly diagram (or month
and year of purchase if product has no
number). Keep this manual and the
receipt in a safe and dry place for future
reference.
cAutIOn, without
the safety alert
symbol, is used to address
practices not related to
personal injury.
ImpORtAnt SAFEty
InStRuctIOnS
InStRuctIOnS pERtAInIng
tO A RISk OF FIRE,
Safety Alert Symbol and Signal
Words
In this manual, on the labeling,
and all other information
provided with this product:
ELEctRIc SHOck, OR
InjuRy tO pERSOnS
WARnIng – When using tools, basic
precautions should always be
this is the safety alert
symbol. It is used to alert
you to potential personal
injury hazards. Obey all
safety messages that
followed, including the following:
general
follow this symbol to avoid
possible injury or death.
a. to reduce the risks of electric
shock, fire, and injury to persons,
read all the instructions before
using the tool.
DAngER indicates
a hazardous
situation which, if not
avoided, will result in death or
serious injury.
Work area
a. keep the work area clean and well
lighted. Cluttered benches and dark
areas increase the risks of electric
shock, fire, and injury to persons.
WARnIng
indicates a
hazardous situation which, if
not avoided, could result in
death or serious injury.
b. Do not operate the tool in
explosive atmospheres, such as in
the presence of flammable liquids,
gases, or dust. The tool is able to
create sparks resulting in the ignition
of the dust or fumes.
cAutIOn, used
with the safety
alert symbol, indicates a
hazardous situation which, if
not avoided, could result in
minor or moderate injury.
c. Keep bystanders, children, and
visitors away while operating the
SKU 98896
For technical questions, please call 1-800-444-3353.
Page 3
tool. Distractions are able to result in
the loss of control of the tool.
conditions. Wear heavy-duty work
gloves during use.
g.
h.
Always wear eye
protection. Wear ANSI-
approved safety goggles.
personal safety
a. Stay alert. Watch what you are
doing and use common sense
when operating the tool. Do not
use the tool while tired or under
the influence of drugs, alcohol, or
medication. A moment of inattention
while operating the tool increases the
risk of injury to persons.
Always wear hearing
protection when using
the tool. Prolonged
exposure to high intensity
noise is able to cause hearing loss.
i.
Risk of Electric Shock. this tool
is not provided with an insulated
gripping surface. Contact with a
″live″ wire will also make exposed
metal parts of the tool ″live″ and
shock the operator.
b. Dress properly. Do not wear loose
clothing or jewelry. contain long
hair. keep hair, clothing, and
gloves away from moving parts.
Loose clothes, jewelry, or long hair
increases the risk of injury to persons
as a result of being caught in moving
parts.
j.
Avoid body contact with grounded
surfaces such as pipes, radiators,
ranges and refrigerators. There is
an increased risk of electric shock if
your body is grounded.
c. Avoid unintentional starting.
Be sure the switch is off before
connecting to the air supply. Do not
carry the tool with your finger on the
switch or connect the tool to the air
supply with the switch on.
k. Explore the workpiece to avoid
contact with hidden wiring.
Thoroughly investigate the workpiece
for possible hidden wiring before
performing work. Contact with live
wiring will shock the operator.
d. Remove adjusting keys and
wrenches before turning the tool
on. A wrench or a key that is left
attached to a rotating part of the tool
increases the risk of personal injury.
tool use and care
a. Use clamps or another practical
way to secure and support the
workpiece to a stable platform.
Holding the work by hand or against
the body is unstable and is able to
lead to loss of control.
e. Do not overreach. keep proper
footing and balance at all times.
Proper footing and balance
enables better control of the tool in
unexpected situations.
b. Do not force the tool. Use the
correct tool for the application. The
correct tool will do the job better and
safer at the rate for which the tool is
designed.
f.
use safety equipment. A
dust mask, non-skid safety
shoes and a hard hat must
be used for the applicable
SKU 98896
For technical questions, please call 1-800-444-3353.
Page 4
c. Do not use the tool if the switch
does not turn the tool on or off.
Any tool that cannot be controlled
with the switch is dangerous and
must be repaired.
Service
a. Tool service must be performed
only by qualified repair personnel.
b. When servicing a tool, use only
identical replacement parts. use
only authorized parts.
d. Disconnect the tool from the
air source before making
any adjustments, changing
c. use only the lubricants supplied
with the tool or specified by the
manufacturer.
accessories, or storing the tool.
Such preventive safety measures
reduce the risk of starting the tool
unintentionally. Turn off and detach
the air supply, safely discharge any
residual air pressure, and release the
throttle and/or turn the switch to its off
position before leaving the work area.
Air source
a.
never connect to an air
source that is capable of
exceeding 90 psi. Over
pressurizing the tool may
e. Store the tool when it is idle out
of reach of children and other
untrained persons. A tool is
dangerous in the hands of untrained
users.
cause bursting, abnormal operation,
breakage of the tool or serious injury
to persons. Use only clean, dry,
regulated compressed air at the rated
pressure or within the rated pressure
range as marked on the tool. Always
verify prior to using the tool that the
air source has been adjusted to the
rated air pressure or within the rated
air-pressure range.
f.
maintain the tool with care. Keep
a cutting tool sharp and clean. A
properly maintained tool, with sharp
cutting edges reduces the risk of
binding and is easier to control.
g. check for misalignment or binding b. Never use oxygen, carbon dioxide,
of moving parts, breakage of
parts, and any other condition
that affects the tool’s operation.
If damaged, have the tool serviced
before using. Many accidents are
caused by poorly maintained tools.
There is a risk of bursting if the tool is
damaged.
combustible gases or any bottled
gas as an air source for the tool.
Such gases are capable of explosion
and serious injury to persons.
SAVE tHESE
InStRuctIOnS.
h. use only accessories that are
identified by the manufacturer for
the specific tool model. Use of an
accessory not intended for use with
the specific tool model, increases the
risk of injury to persons.
SKU 98896
For technical questions, please call 1-800-444-3353.
Page 5
factors which cannot be built into this
product, but must be supplied by the
operator.
SymBOLS AnD
SpEcIFIc SAFEty
InStRuctIOnS
2. WARNING: Some dust created by
power sanding, sawing, grinding,
drilling, and other construction
activities, contains chemicals
Symbol Definitions
Symbol
property or statement
known [to the State of California] to
cause cancer, birth defects or other
reproductive harm. Some examples
of these chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks and
cement or other masonry products
• Arsenic and chromium from
chemically treated lumber
Your risk from these exposures
varies, depending on how often you
do this type of work. To reduce your
exposure to these chemicals: work in
a well ventilated area, and work with
approved safety equipment, such as
those dust masks that are specially
designed to filter out microscopic
particles. (California Health & Safety
Code § 25249.5, et seq.)
WARNING: The brass components
of this product contain lead, a
chemical known to the State of
California to cause birth defects (or
other reproductive harm). (California
Health & Safety code § 25249.5, et
seq.)
No-load speed
n
o
Revolutions or reciprocation per
minute
.../min
pSI
Pounds per square inch of pressure
Foot-pounds of torque
ft-lb
Blows per minute
Bpm
cFm
ScFm
npt
Cubic Feet per Minute flow
Cubic Feet per Minute flow at
standard conditions
National pipe thread, tapered
National pipe thread, straight
npS
WARNING marking concerning Risk
of Eye Injury. Wear ANSI-approved
eye protection.
WARNING marking concerning Risk
of Hearing Loss. Wear hearing
protection.
WARNING marking concerning Risk
of Respiratory Injury. Wear NIOSH-
approved dust mask/respirator.
WARNING marking concerning Risk
of Explosion.
3. Only use with accessories rated to
handle the forces exerted by this tool
during operation. Other accessories
not designed for the forces generated
may break and forcefully launch
pieces.
Specific Safety Instructions
1. The warnings and precautions
discussed in this manual cannot
cover all possible conditions and
situations that may occur. It must
be understood by the operator that
common sense and caution are
4. Attach all accessories properly to the
tool before connecting the air supply.
A loose accessory may detach or
break during operation.
SKU 98896
For technical questions, please call 1-800-444-3353.
Page 6
5. Obey the manual for the air
compressor used to power this tool.
3. Wear suitable gloves to reduce the
vibration effects on the user.
6. Install an in-line shutoff valve to allow 4. Use tools with the lowest vibration
immediate control over the air supply
in an emergency, even if a hose is
ruptured.
when there is a choice between
different processes.
5. Include vibration-free periods each
day of work.
7. Use this tool with both hands only.
Using tools with only one hand can
result in loss of control.
6. Grip tool as lightly as possible (while
still keeping safe control of it). Let
the tool do the work.
8. Do not lay the tool down until it has
come to a complete stop. Moving
parts can grab the surface and pull
the tool out of your control.
7. To reduce vibration, maintain tool as
explained in this manual. If abnormal
vibration occurs, stop immediately.
Vibration precautions
SAVE tHESE
InStRuctIOnS.
This tool vibrates during use.
Repeated or long-term exposure to
vibration may cause temporary or
permanent physical injury, particularly to
the hands, arms and shoulders. To reduce
the risk of vibration-related injury:
1. Anyone using vibrating tools regularly
or for an extended period should
first be examined by a doctor and
then have regular medical check-
ups to ensure medical problems are
not being caused or worsened from
use. Pregnant women or people
who have impaired blood circulation
to the hand, past hand injuries,
nervous system disorders, diabetes,
or Raynaud’s Disease should not
use this tool. If you feel any medical
or physical symptoms related to
vibration (such as tingling, numbness,
and white or blue fingers), seek
medical advice as soon as possible.
2. Do not smoke during use. Nicotine
reduces the blood supply to the
hands and fingers, increasing the risk
of vibration-related injury.
SKU 98896
For technical questions, please call 1-800-444-3353.
Page 7
refer to the Assembly Diagram near
the end of this manual.
FunctIOnAL DEScRIptIOn
Specifications
unpacking
Air Pressure Range
90 PSI
When unpacking, check to make sure
that the item is intact and undamaged. If
any parts are missing or broken, please
call Harbor Freight Tools at the number
shown throughout the manual as soon as
possible.
Maximum Air Pressure 90 PSI
Air Inlet
1/4" -18 NPT
Maximum Speed*
Air Consumption
Arbor/Chuck Capacity
700 RPM
5 CFM @ 90 PSI
1/16 - 1/2"
* Maximum speed at stated maximum air pressure.
Excess air pressure is hazardous and may cause the
tool to exceed stated maximum speed.
• This air tool may be shipped with a
protective plug covering the air inlet.
Remove this plug before set up.
components and controls
Air Supply
tO pREVEnt
ExpLOSIOn:
use only clean, dry, regulated,
compressed air to power this
tool. Do not use oxygen,
carbon dioxide, combustible
gases, or any other bottled
gas as a power source for this
tool.
Trigger
Forward/Reverse
Lever
Fig. 1
1. Reversible feature controled by the
Forward/Reverse lever next to the
power trigger. (See Fig. 1.) Move
switch up toward “F” for forward and
down toward “R” for reverse
InItIAL tOOL SEt up/
ASSEmBLy
Read the EntIRE ImpORtAnt
SAFEty InFORmAtIOn
section at the beginning of this
manual including all text under
subheadings therein before set
up or use of this product.
Fig. 2
1. Incorporate an in-line oiler, shut-off
valve, regulator with pressure gauge,
note: For additional information regarding
the parts listed in the following pages,
SKU 98896
For technical questions, please call 1-800-444-3353.
Page 8
and filter for best service, as shown
in the diagram above. An in-line
shutoff valve is an important
safety device because it controls
the air supply even if the air hose
is ruptured. (See Fig. 2.)
5. Close the in-line safety valve between
the compressor and the tool.
6. Turn on the air compressor according
to the manufacturer’s directions and
allow it to build up pressure until it
cycles off.
note: If an automatic oiler system is not
used, add a few drops of Pneumatic
Tool Oil to the airline connection
before operation. Add a few more
drops after each hour of continual
use. Oiling location is engraved into
the bottom of the handle next to the
drill’s air inlet.
7. Adjust the air compressor’s output
regulator so that the air output is
enough to properly power the tool,
but the output will not exceed the
tool’s maximum air pressure at any
time. Adjust the pressure gradually,
while checking the air output gauge
to set the right pressure range.
2. Attach an air hose to the
compressor’s air outlet. Connect
the air hose to the air inlet of the
tool. Other components, such as
a connector and quick coupler, will
make operation more efficient, but
are not required.
8. Inspect the air connections for leaks.
Repair any leaks found.
9. If the tool will not be used at this
time, turn off and detach the air
supply, safely discharge any
residual air pressure, and release
the throttle and/or turn the switch to
its off position to prevent accidental
operation.
WARnIng! tO pREVEnt SERIOuS
InjuRy FROm AccIDEntAL
OpERAtIOn:
Do not install a female quick
coupler on the tool. Such a coupler
contains an air valve that will allow
the air tool to retain pressure and
operate accidentally after the air
supply is disconnected.
note: Residual air pressure should not be
present after the tool is disconnected
from the air supply. However, it is a
good safety measure to attempt to
discharge the tool in a safe fashion
after disconnecting to ensure that the
tool is disconnected and unpowered.
note: Air flow, and therefore tool
performance, can be hindered by
undersized air supply components.
3. The air hose must be long enough
to reach the work area with enough
extra length to allow free movement
while working.
4. Make sure the tool’s throttle or
switch is in the off position; refer to
Operation section for description of
controls.
SKU 98896
For technical questions, please call 1-800-444-3353.
Page 9
ID Air Source Hose (not included).
Connect the Air Source Hose to the
Drill.
OpERAtIng InStRuctIOnS
Read the EntIRE ImpORtAnt
SAFEty InFORmAtIOn
section at the beginning of this
manual including all text under
subheadings therein before set
up or use of this product.
note: If you are not using an automatic
oiler system, before operation, add a
few drops of Pneumatic Tool Oil to the
airline connection. Add a few drops
more after each hour of continual
use.
Inspect tool before use, looking
for damaged, loose, and
missing parts. If any problems
are found, do not use tool until
repaired.
2. Settheairpressureonyourcompressor
to 90 PSI. Do not exceed the maximum
air pressure of 90 PSI.
3. Check the air connection for leaks.
Warning! Always disconnect the unit from
the air compressor when changing
bits.
tool Set up
tO pREVEnt
SERIOuS InjuRy
FROm AccIDEntAL
Warning! After drilling, the bit will be
extremely hot. Do not touch it until it
has had ample time to cool down.
OpERAtIOn:
turn off the tool, detach the
air supply, safely discharge
any residual air pressure in
the tool, and release the
throttle and/or turn the switch
to its off position before
performing any inspection,
maintenance, or cleaning
procedures.
note: To reverse the drill’s direction, flip the
Reverse Lever on the handle down.
(See Fig.1).
4. to install the handle: Slide the
Handle Ring (35) over the clamp nut
(30) in the desired position. Install the
Handle (34) over the threaded portion
of the Handle Ring (35) and tighten
securely.
tO pREVEnt SERIOuS
InjuRy:
5. Insert the chuck key (36) into one of
the holes in the chuck (32) and turn it
counterclockwise to open the jaws.
Do not adjust or tamper with
any control or component in a
way not specifically explained
within this manual. Improper
adjustment can result in
tool failure or other serious
hazards.
6. Insert the bit and hand tighten it, then
tighten it with the chuck key (36) by
turning it clockwise.
7. With heavy leather gloves on, tug on
the bit and make sure it is securely
attached. Check that it is straight.
1. You will need to prepare a 1/4" air
connector to connect to the Air Inlet
(13) on the Drill. First, wrap the 1/4"
air connector with pipe thread seal
tape before connecting to a 1/4"
note: Always use sharp bits. Dull or
damaged bits may cause undue stress
on the drill and possibly break causing
injury. Bits are available at Harbor
Freight Tools.
SKU 98896
For technical questions, please call 1-800-444-3353.
Page 10
3. When drilling wood, place the bit
at the point to be drilled. If you are
drilling a hard, smooth surface, use
a punch to mark the drill location.
Grasp the drill firmly with both hands
while slowly squeezing the Trigger
(8). Never force the tool. Only apply
light pressure when horizontal drilling.
8. Securely clamp your workpiece.
Work piece and Work Area Set up
1. Designate a work area that is clean
and well-lit. The work area must not
allow access by children or pets to
prevent injury and distraction.
Note: When drilling plastics or plastic coated
chip board, follow the same directions
as stated in number 9 for wood.
2. Route the air hose along a safe
route to reach the work area without
creating a tripping hazard or exposing
the air hose to possible damage.
The air hose must be long enough
to reach the work area with enough
extra length to allow free movement
while working.
Note: If a bit becomes wedged into the
workpiece, remove it from the drill
and use the appropriate hand tools to
remove it.
4. When drilling metal, always use a
punch to mark the drilling position.
Use a cutting oil with most metals, to
prolong the life of the bit and increase
the drilling action. With steel, tin, and
sheet metal use a light machine oil,
with aluminum, use paraffin. Do not
use lubricants with brass, copper, and
cast iron. Grasp the drill firmly with
both hands and follow the directions
given in #9 above.
3. Secure loose workpieces using a vise
or clamps (not included) to prevent
movement while working.
4. There must not be hazardous objects
(such as utility lines or foreign
objects) nearby that will present a
hazard while working.
general Operating Instructions
1. If an automatic oiler is not used, add
a few drops of Pneumatic Tool Oil
to the airline connection before use.
Add a few drops more after each
hour of continual use.
5. When done drilling, release pressure
on the Trigger (8). The drill will slow
to a stop. Disconnect the Air Drill
from the air compressor hose.
6. To prevent accidents, turn off the
tool, detach the air supply, safely
discharge any residual air pressure in
the tool, and release the throttle and/
or turn the switch to its off position
after use. Clean external surfaces
of the tool with clean, dry cloth, and
apply a thin coat of tool oil. Then
store the tool indoors out of children’s
reach.
2. If the tool requires more force to
accomplish the task, verify that the
tool receives sufficient, unobstructed
airflow (CFM) and increase the
pressure (PSI) output of the regulator
up to the maximum air pressure
rating of this tool. cAutIOn! tO
pREVEnt tOOL AnD AccESSORy
FAILuRE, RESuLtIng In InjuRy:
Do not exceed the tool’s maximum
air pressure rating. If the tool still
does not have sufficient force at
maximum pressure and sufficient
airflow, then a larger tool may be
required.
SKU 98896
For technical questions, please call 1-800-444-3353.
Page 11
cleaning, maintenance, and
Lubrication
uSER-mAIntEnAncE
InStRuctIOnS
note: These procedures are in addition to
the regular checks and maintenance
explained as part of the regular
Procedures not specifically
explained in this manual
must be performed only by a
qualified technician.
operation of the air-operated tool.
1. Daily - Air Supply maintenance:
Every day, perform maintenance
on the air supply according to
tO pREVEnt
SERIOuS InjuRy
FROm AccIDEntAL
the component manufacturers’
instructions. The lubricator’s oil
level needs to be maintained and
the moisture filter must be regularly
drained. Performing routine
maintenance on the air supply will
allow the tool to operate more safely
and will also reduce wear on the tool.
OpERAtIOn:
turn off the tool, detach the
air supply, safely discharge
any residual air pressure in
the tool, and release the
throttle and/or turn the switch
to its off position before
performing any inspection,
maintenance, or cleaning
procedures.
2. Weekly - grease Lubrication:
Lubricate the internal mechanism of
the tool, using white lithium grease
through the grease fittings. See
Lubrication Diagram below.
tO pREVEnt SERIOuS
InjuRy FROm tOOL
FAILuRE:
Do not use damaged
3. Quarterly (every 3 months) - tool
Disassembly, cleaning, and
Inspection:
equipment. If abnormal
noise, vibration, or leaking
air occurs, have the problem
corrected before further use.
Have the internal mechanism
cleaned, inspected, and lubricated by
a qualified technician. If the vanes
need replacement, all vanes should
be replaced as a set.
tO pREVEnt ExpLOSIOn:
Lubricate the tool only
with specified lubricants.
Lubricate the air inlet
using only pneumatic tool
oil. Lubricate the internal
mechanism using only
white lithium grease. Other
lubricants may damage the
mechanism and may be
highly flammable, causing an
explosion.
SKU 98896
For technical questions, please call 1-800-444-3353.
Page 12
troubleshooting
problem
possible causes
Likely Solutions
Decreased output. 1. Not enough air pressure and/ 1. Check for loose connections and make sure
or air flow.
that air supply is providing enough air flow
(CFM) at required pressure (PSI) to the
tool’s air inlet. Do not exceed maximum air
pressure.
2. Obstructed trigger.
2. clean around trigger to ensure free
movement.
3. Incorrect lubrication or not
enough lubrication.
3. Lubricate using air tool oil and grease
according to directions.
4. Blocked air inlet screen (if
equipped).
4. Clean air inlet screen of buildup.
5. Air leaking from loose housing. 5. Make sure housing is properly assembled
and tight.
6. Mechanism contaminated.
6. Have qualified technician clean and lubricate
mechanism. Install in-line filter in air supply
as stated in Initial Set Up: Air Supply.
7. Vane wear or damage.
7. Replace all vanes.
Housing heats
during use.
1. Incorrect lubrication or not
enough lubrication.
1. Lubricate using air tool oil and grease
according to directions.
2. Worn parts.
2. Have qualified technician inspect internal
mechanism and replace parts as needed.
1. Check for incorrect alignment and uneven
gaps. If cross-threaded, disassemble and
replace damaged parts before use.
Severe air
leakage.
1. Cross-threaded housing
components.
(Slight air leakage
is normal,
especially on older
tools.)
2. Loose housing.
2. Tighten housing assembly. If housing cannot
tighten properly, internal parts may be
misaligned.
3. Damaged valve or housing.
3. Replace damaged components.
4. Dirty, worn or damaged valve. 4. Clean or replace valve assembly.
Follow all safety precautions whenever diagnosing or servicing the
tool. Disconnect air supply before service.
SKU 98896
For technical questions, please call 1-800-444-3353.
Page 13
pLEASE READ tHE FOLLOWIng
pARtS LISt
cAREFuLLy
part
Description
Q’ty
1
1
1
1
3
1
1
1
1
1
1
2
1
2
1
1
5
1
1
1
1
1
6
6
1
1
1
2
2
1
1
1
1
1
1
1
1
THE MANUFACTURER AND/OR DISTRIBUTOR
HASPROVIDEDTHEPARTSLISTANDASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE
TOOLONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION
OR WARRANTY OF ANY KIND TO THE BUYER
THAT HE OR SHE IS qUALIFIED TO MAKE ANY
REPAIRS TO THE PRODUCT, OR THAT HE OR
SHE IS qUALIFIED TO REPLACE ANY PARTS OF
THE PRODUCT. IN FACT, THE MANUFACTURER
AND/OR DISTRIBUTOR ExPRESSLY STATES
THATALLREPAIRSANDPARTSREPLACEMENTS
SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE
BUYER. THE BUYER ASSUMES ALL RISK AND
LIABILITYARISINGOUTOFHISORHERREPAIRS
TOTHEORIGINALPRODUCTORREPLACEMENT
PARTS THERETO, OR ARISING OUT OF HIS OR
HER INSTALLATION OF REPLACEMENT PARTS
THERETO.
1
2
3
4
5
6
7
8
9
Housing
O-Ring
O-Ring
Valve Stem
O-Ring
Bushing
Trigger Spring
Trigger
Trigger Screw
10 Pin
11 Muffler Cover
12 Screw
13 Air Inlet
14 Bearing
15 End Plate
16 Rotor
17 Rotor Blade
18 Cylinder
19 Pin
20 Front Plate
21 Washer
22 Gear
23 Gear
24 Pin
25 Gear Plate
26 Gear
27 Work Spindle
28 Thread Ring Gear
29 Bearing
30 Clamp Nut
31 Washer
32 Chuck
33 Chuck Screw
34 Handle
35 Handle Ring
36 Chuck Key (See Cover Photo)
37 Air Coupler/Fitting (Not Shown)
SKU 98896
For technical questions, please call 1-800-444-3353.
Page 14
ASSEmBLy DIAgRAm
# 36 Chuck Key not shown
# 37 Air Coupler/Fitting not shown
Record product’s Serial number Here:
note: If product has no serial number, record month and year of purchase instead.
note: Some parts are listed and shown for illustration purposes only, and are not
available individually as replacement parts.
SKU 98896
For technical questions, please call 1-800-444-3353.
Page 15
LImItED 1 yEAR WARRAnty
Harbor Freight Tools Co. makes every effort to assure that its products meet
high quality and durability standards, and warrants to the original purchaser that
this product is free from defects in materials and workmanship for the period of one
year from the date of purchase (90 days if used by a professional contractor or if
used as rental equipment). This warranty does not apply to damage due directly or
indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside
our facilities, normal wear and tear, or to lack of maintenance. We shall in no event be
liable for death, injuries to persons or property, or for incidental, contingent, special
or consequential damages arising from the use of our product. Some states do not
allow the exclusion or limitation of incidental or consequential damages, so the above
limitation of exclusion may not apply to you. THIS WARRANTY IS ExPRESSLY IN
LIEU OF ALL OTHER WARRANTIES, ExPRESS OR IMPLIED, INCLUDING THE
WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us
with transportation charges prepaid. Proof of purchase date and an explanation of the
complaint must accompany the merchandise. If our inspection verifies the defect, we
will either repair or replace the product at our election or we may elect to refund the
purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that
the defect resulted from causes not within the scope of our warranty, then you must
bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights
which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
SKU 98896
For technical questions, please call 1-800-444-3353.
Page 16
|