18V RECIPROCATING SAW
93830
ASSEMBLY AND OPERATING INSTRUCTIONS
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
TO PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
©
®
Copyright 2005 by Harbor FreightTools . All rights reserved. No portion of this manual or
any artwork contained herein may be reproduced in any shape or form without the express
written consent of Harbor FreightTools.
For technical questions and replacement parts, please call 1-800-444-3353.
PRODUCT SPECIFICATIONS
Item
Description
Input: 120 VAC / 60 Hz
Output: 24 VDC, 400 mA
AC Charger Adapter
Charge Time: 3 to 5 Hours; 8 Hour Initial Charge
Reciprocating Saw
Accessories
7/8" Stroke; 0-2300 SPM; Safety Trigger
1 Rechargeable 18 VDC Battey; Battery Charger/ Adapter
SaveThis Manual
You will need this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures, parts list and assembly
diagram. Keep your invoice with this manual. Write the invoice number on the inside
of the front cover. Keep this manual and invoice in a safe and dry place for future
reference.
GENERAL SAFETY RULES
WARNING!
READ AND UNDERSTAND ALL INSTRUCTIONS
Failure to follow all instructions listed below may result in
electric shock, fire, and/or serious injury.
SAVE THESE INSTRUCTIONS
Work Area
1.
2.
Keep your work area clean and well lit. Cluttered benches and dark areas invite
accidents.
Do not operate power tools in explosive atmospheres, such as in the presence
of flammable liquids, gases, or dust. Power tools create sparks which may ignite
the dust or fumes.
SKU 93830
For technical questions, please call 1-800-444-3353.
Page 3
3.
4.
5.
6.
Keep bystanders, children, and visitors away while operating a power tool.
Distractions can cause you to lose control. Protect others in the work area from
debris such as chips and sparks. Provide barriers or shields as needed. Do not
allow children to handle or play with these products.
Electrical Safety
Grounded tools must be plugged into an outlet properly installed and grounded
in accordance with all codes and ordinances. Never remove the grounding
prong or modify the plug in any way. Do not use any adapter plugs. Check
with a qualified electrician if you are in doubt as to whether the outlet is properly
grounded. If the tools should electrically malfunction or break down, grounding
provides a low resistance path to carry electricity away from the user.
Double insulated tools are equipped with a polarized plug (one blade is wider
than the other). This plug will fit in a polarized outlet only one way. If the plug
does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a
qualified electrician to install a polarized outlet. Do not change the plug in any
way. Double insulation
eliminates the need for the three wire grounded power
cord and grounded power supply system.
Avoid body contact with grounded surfaces such as pipes, radiators, ranges,
and refrigerators. There is an increased risk of electric shock if your body is
grounded.
7.
8.
Do not expose power tools to rain or wet conditions. Water entering a power
tool will increase the risk of electric shock.
Do not abuse the Power Cord. Never use the Power Cord to carry the tools or
pull the Plug from an outlet. Keep the Power Cord away from heat, oil, sharp
edges,or moving parts. Replace damaged Power Cords immediately. Damaged
Power Cords increase the risk of electric shock.
9.
When operating a power tool outside, use an outdoor extension cord marked
“W-A”or“W”. These extension cords are rated for outdoor use, and reduce the risk
of electric shock.
Personal Safety
10.
11.
Stay alert. Watch what you are doing, and use common sense when operating
a power tool. Do not use a power tool while tired or under the influence of
drugs, alcohol, or medication. A moment of inattention while operating power
tools may result in serious personal injury.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep
your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry,
or long hair can be caught in moving parts.
SKU 93830
For technical questions, please call 1-800-444-3353.
Page 4
12.
13.
Avoid accidental starting. Be sure the Power Switch is off before plugging in.
Carrying power tools with your finger on the Power Switch, or plugging in power
tools with the Power Switch on, invites accidents.
Remove adjusting keys or wrenches before turning the power tool on. A wrench
or a key that is left attached to a rotating part of the power tool may result in personal
injury.
14.
15.
Do not overreach. Keep proper footing and balance at all times. Proper footing
and balance enables better control of the power tool in unexpected situations.
Use safety equipment. Always wear eye protection. Dust mask, nonskid safety
shoes, hard hat, or hearing protection must be used for appropriate conditions.
Always wear ANSI approved safety goggles and a dust mask/respirator when using
or performing maintenance on this tool.
Tool Use and Care
16.
17.
Use clamps (not included) or other practical ways to secure and support the
workpiece to a stable platform. Holding the work by hand or against your body is
unstable and may lead to loss of control.
Do not force the tool. Use the correct tool for your application. The correct tool
will do the job better and safer at the rate for which it is designed. Do not force the
tool and do not use the tool for a purpose for which it is not intended. Do not modify
this product.
18.
19.
Do not use the power tool if the Power Switch does not turn it on or off. Any
tool that cannot be controlled with the Power Switch is dangerous and must be
replaced.
Disconnect the Power Cord Plug from the power source before making any
adjustments, changing accessories, or storing the tool. Such preventive safety
measures reduce the risk of starting the tool accidentally. Always unplug the tool
from its electrical outlet before performing any inspection, maintenance, or
cleaning procedures.
20.
21.
Store idle tools out of reach of children and other untrained persons. Tools are
dangerous in the hands of untrained users.
Maintain tools with care. Keep cutting tools sharp and clean. Properly
maintained tools with a sharp cutting edge are less likely to bind and are easier to
control. Do not use a damaged tool. Tag damaged tools “Do not use” until repaired.
22.
Check for misalignment or binding of moving parts, breakage of parts, and
any other condition that may affect the tool’s operation. If damaged, have the
tool serviced before using. Many accidents are caused by poorly maintained
tools.
SKU 93830
For technical questions, please call 1-800-444-3353.
Page 5
23.
Use only accessories that are recommended by the manufacturer for your
model. Accessories that may be suitable for one tool may become hazardous when
used on another tool.
Service
24.
25.
Tool service must be performed only by qualified repair personnel. Service or
maintenance performed by unqualified personnel could result in a risk of injury.
When servicing a tool, use only identical replacement parts. Follow instructions
in the “Inspection, Maintenance, And Cleaning”section of this manual. Use of
unauthorized parts or failure to follow maintenance instructions may create a risk of
electric shock or injury.
Grounding
WARNING!
Improperly connecting the grounding wire can result in the risk of electric
shock. Check with a qualified electrician if you are in doubt as to whether the
outlet is properly grounded. Do not modify the power cord plug provided with
the tool. Never remove the grounding prong from the plug. Do not use the
tool if the power cord or plug is damaged. If damaged, have it repaired by a
service facility before use. If the plug will not fit the outlet, have a proper outlet
installed by a qualified electrician.
GroundedTools:ToolsWithThree Prong Plugs
1.
2.
Tools marked with “Grounding Required” have a three wire cord and three prong
grounding plug. The plug must be connected to a properly grounded outlet. If the
tool should electrically malfunction or break down, grounding provides a low
resistance path to carry electricity away from the user, reducing the risk of electric
shock. (See Figure A.)
The grounding prong in the plug is connected through the green wire inside the
cord to the grounding system in the tool. The green wire in the cord must be the only
wire connected to the tool’s grounding system and must never be attached to an
electrically “live” terminal. (See Figure A.)
SKU 93830
For technical questions, please call 1-800-444-3353.
Page 6
3.
Your tool must be plugged into an appropriate outlet, properly installed and grounded
in accordance with all codes and ordinances. The plug and outlet should look like
those in the following illustration. (See Figure A.)
FIGURE A
Double InsulatedTools:ToolsWithTwo Prong Plugs
4.
5.
Tools marked “Double Insulated” do not require grounding. They have a special
double insulation system which satisfies OSHA requirements and complies with
the applicable standards of Underwriters Laboratories, Inc., the Canadian Standard
Association, and the National Electrical Code. (See Figure B.)
Double insulated tools may be used in either of the 120 volt outlets shown in the
following illustration. (See Figure B.)
FIGURE B
Extension Cords
1.
2.
Grounded tools require a three wire extension cord. Double Insulated tools can
use either a two or three wire extension cord.
As the distance from the supply outlet increases, you must use a heavier gauge
extension cord. Using extension cords with inadequately sized wire causes a serious
drop in voltage, resulting in loss of power and possible tool damage.
(See Figure C, next page.)
3.
The smaller the gauge number of the wire, the greater the capacity of the cord. For
example, a 14 gauge cord can carry a higher current than a 16 gauge cord.
(See Figure C.)
SKU 93830
For technical questions, please call 1-800-444-3353.
Page 7
4.
5.
When using more than one extension cord to make up the total length, make sure
each cord contains at least the minimum wire size required. (See Figure C.)
If you are using one extension cord for more than one tool, add the nameplate
amperes and use the sum to determine the required minimum cord size.
(See Figure C.)
6.
7.
If you are using an extension cord outdoors, make sure it is marked with the suffix
“W-A” (“W” in Canada) to indicate it is acceptable for outdoor use.
Make sure your extension cord is properly wired and in good electrical condition.
Always replace a damaged extension cord or have it repaired by a qualified
electrician before using it.
8.
Protect your extension cords from sharp objects, excessive heat, and damp or wet
areas.
RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS*
NAMEPLATE
AMPERES
(At Full Load)
EXTENSION CORD LENGTH
25 Feet
18
50 Feet
75 Feet
100 Feet
150 Feet
0 - 2.0
2.1 - 3.4
18
18
18
16
14
12
10
18
18
16
14
12
10
-
18
16
14
12
10
-
16
14
12
12
-
18
3.5 - 5.0
18
5.1 - 7.0
18
7.1 - 12.0
12.1 - 16.0
16.1 - 20.0
18
14
-
12
-
-
* Based on limiting the line voltage drop to five
volts at 150% of the rated amperes.
FIGURE C
Symbology
SKU 93830
For technical questions, please call 1-800-444-3353.
Page 8
Specific Safety Rules
1.
Maintain a safe working environment. Make sure there is adequate surrounding
workspace. Always keep the work area free of obstructions, grease, oil, trash, and
other debris.
2.
3.
4.
Maintain labels and nameplates on this item. These carry important information.
If unreadable or missing, contact Harbor Freight Tools for a replacement.
When using a handheld power tool, always maintain a firm grip on the tool
with both hands.
To avoid electrical shock, do not pull or carry the AC Charger Adapter (53) by
its Power Cord or pull the Power Cord around sharp corners or edges. Do not
unplug the AC Charger Adapter by pulling on the Power Cord. Keep the Power
Cord away from heated surfaces.
5.
6.
Never leave the AC Charger Adapter (53) unattended when it is plugged in.
Make sure to unplug the AC Charger Adapter from its outlet before leaving.
Proper Battery Care: Battery (47) leakage may occur under extreme usage or
temperature conditions. If Battery fluid comes in contact with skin, wash with soap
and water and rinse with lemon juice and vinegar. If the fluid comes in contact with
eyes, flush with water for several minutes and contact a doctor immediately. Never
burn the Battery, as it can explode in a fire. Do not attempt to charge a leaking
Battery. Contact local solid waste authorities for instructions on correct disposal or
recycling of the Battery.
7.
Store idle equipment. When not in use, tools and equipment should be stored in a
dry location to inhibit rust. Always lock up tools and equipment, and keep out of
reach of children.
8.
9.
Industrial applications must follow OSHA requirements.
WARNING! Some dust created by power sanding, sawing, grinding, drilling,
and other construction activities, contain chemicals known (to the State of California)
to cause cancer, birth defects or other reproductive harm. Some examples of these
chemicals are: lead from lead-based paints, crystalline silica from bricks and cement
or other masonry products, arsenic and chromium from chemically treated lumber.
Your risk from these exposures varies, depending on how often you do this type of
work. To reduce your exposure to these chemicals: work in a well ventilated area,
and work with approved safety equipment, such as those dust masks that are specially
designed to filter out microscopic particles. (California Health & Safety Code §
25249.5, et seq.)
10.
11.
WARNING! People with pacemakers should consult their physician(s) before
using this product. Electromagnetic fields in close proximity to a heart pacemaker
could cause interference to or failure of the pacemaker.
WARNING! The warnings, precautions, and instructions discussed in this manual
cannot cover all possible conditions and situations that may occur. The operator
must understand that common sense and caution are factors which cannot be built
into this product, but must be supplied by the operator.
SKU 93830
For technical questions, please call 1-800-444-3353.
Page 9
CHARGINGTHE BATTERY
Note: Always switch to a fresh battery when tool performance begins to diminish.
Severe heat is most destructive to a battery; the more heat generated, the faster the
battery loses power. A battery that gets too hot can be permanently damaged. Never
over-discharge a battery by using the tool even after tool performance is decreasing.
Never attempt to discharge a tool’s battery by continuing to pull the tool trigger.When
tool performance begins to diminish, stop the tool, recharge the battery and
use the fresh battery for optimal performance.
1.
When a Battery (47) requires recharging, a 3 to 5 hour* charge allows the tool to
operate at full power. Do not recharge the Battery longer than 5 hours*, as damage
to the Battery and/or tool will occur.
2.
To charge the Battery (47), plug the AC Charger Adapter’s (53) plug into the Charger
(52). Insert the Charger (52) onto the top of the Battery (47) until it locks into place.
Charging room temperature: 50° F - 104° F. Then, plug the AC Charger Adapter
into the nearest 120 Volt, grounded, electrical outlet. (See illustration below.)
3.
Two Charging Indicator LEDs on the Charger (52) will illuminate to show that charging
is taking place. NOTE: The AC Charger Adapter (53) will not automatically turn off
when the Battery is fully charged, and the Charging Indicator LEDs will remain on
until the AC Charger Adapter is disconnected from the electrical outlet. Recharging
the Battery more than 5 hours* can cause damage to the battery cells.
4.
5.
While charging, the Battery (47), AC Charger Adapter (53), and/or Charger (52)
may become warm to the touch. This is normal, and does not indicate a problem.
Once the Battery (47) is fully charged, disconnect the AC Charger Adapter (53) from
the electrical outlet. Then, disconnect the Charger from the Battery.
* The Battery (47) require an initial charge time of 8 hours. Do not recharge the Battery more than 5
hours after this initial charging.
SKU 93830
For technical questions, please call 1-800-444-3353.
Page 10
OPERATION
Note: For additional information regarding the parts listed in the following pages, refer to
the Assembly Diagrams at the end of the manual.
Reciprocating Saw
WARNING: Always make sure the Battery (47) of the Reciprocating Saw is removed prior
to making any adjustments to the tool.
1.
Slide the Battery (47) into the base of the Reciprocating saw.
Note: Do not start the Reciprocating Saw if the Saw Blade (23) is in contact with anything
before operation. If necessary, lift the Reciprocating Saw to free the Saw Blade
before squeezing the Trigger.
2.
3.
4.
NEVER cut into areas where you cannot identify any possible hazards behind or
inside the surface being cut.
Hold the Reciprocating Saw firmly with both hands, then slide the Safety (37) to one
side and squeeze the Trigger (41) to start the Saw.
With the Reciprocating Saw “ON”, place the Saw Blade (23) against the material to
be cut. Press down slightly on the Reciprocating Saw to help it cut, but allow the
saw to do the work.
5.
6.
Once the cutting procedure is completed, release pressure on the Trigger (41) to
stop the Reciprocating Saw. Then, remove the Battery (47).
Saw Blade Installation/Replacement:
A. Remove the Battery (47) from the tool.
B. With a Hex Wrench (not provided), loosen the front Cap Screw (29).
(See illustration above.)
C. Slide the Saw Blade (23) teeth-down into the Blade Holder (28) as far as possible.
D. Then, firmly retighten the Cap Screw (29) to secure the Saw Blade (23) in place.
E. Gently pull on the Blade (23) with a gloved hand to ensure it is held properly.
SKU 93830
For technical questions, please call 1-800-444-3353.
Page 11
INSPECTION, MAINTENANCE, AND CLEANING
1.
2.
WARNING! Always remove the Battery Pack (47) from a tool and unplug
the AC Charger Adapter (53) from its electrical outlet before performing any
inspection, maintenance, or cleaning on the tool.
BEFORE EACH USE, inspect the general condition of the tool. Check for
misalignment or binding of moving parts, cracked or broken parts, damaged wiring,
and any other condition that may affect its safe operation. If abnormal noise or
vibration occurs with a tool, have the problem corrected before further use. Do not
use damaged equipment.
3.
4.
TO CLEAN, use a clean, slightly damp cloth to clean the outer surfaces of the tool.
A mild detergent may be used. Do not use solvents. Do not immerse the tool,
Battery, or AC Charger Adapter in water.
WHEN STORING, always keep this tool and accessories in a clean, dry location
out of reach of children. Keep charger unplugged from the wall outlet when not in
use.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDEDTHE PARTS DIAGRAM INTHIS MANUAL
AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY
REPRESENTATION ORWARRANTY OF ANY KINDTOTHE BUYERTHAT HE OR SHE IS QUALIFIEDTO
MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY
PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATESTHAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED
AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND
LIABILITY ARISING OUT OF HIS OR HER REPAIRSTOTHE ORIGINAL PRODUCT OR REPLACEMENT
PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS
THERETO.
SKU 93830
For technical questions, please call 1-800-444-3353.
Page 12
PARTS LISTS AND DIAGRAMS
Parts List/Diagram - Reciprocating Saw
Part
1
Description
Q'ty Part
19 Motor Gear
20 Bolt M4x10
Description
Q'ty Part
37 Safety
38 Ferrite Bead
Description
Q'ty
1
Bolt M4x12
13
1
1
1
1
1
1
4
4
3
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
3
1
1
1
1
1
1
1
2
Right Housing Cover
Right Housing
Clip
2
3
21 Gearbox Housing
22 Motor
39 Red Wire
1
4
40 Black Wire
41 Trigger
1
5
Bearing
23 Blade
1
6
Washer
24 Foot
42 Radiator
1
7
Clip
25 Foot Pivot
26 Clip
43 Red Wire
1
8
Spring Washer
Bolt M4x12
44 Black Wire
45 Connector
46 Terminal
1
9
27 Foot Bracket
28 Blade Holder
29 Cap Screw M4x8
30 Shaft
1
10 Planet Gear
11 Sway Bearing
12 Drive Pin
13 Clip
1
47 Battery
1
48 Left Housing
49 Left Housing Cover
50 Grommet
1
31 Pin
1
14 Gear Axis
15 Bearing
32 Bearing Cover
33 Pad
2
51 Machine Screw M3x6
52 Charger
1
16 Gearbox Cover
17 Gear Ring
18 Back Plate
34 Oilless Bearing
35 Oilless Bearing
36 Spring
1
53 AC Charger Adapter
1
Trigger Switch is an assembly:
41, 42, 43, 44, 45, 46, 50, 51
Part 52 - Charger - not shown.
Part 53 - AC Charger Adapter - not shown.
SKU 93830
For technical questions, please call 1-800-444-3353.
Page 13
|