Haier Washer 50FREE 3B User Manual

Fully Automatic Washing Machine  
User's manual  
This manual is for  
50FREE-3B  
Please read this manual  
carefully before using.  
Retain it for future reference.  
Special number:0030805269B  
 
Trouble-shooting answer to question  
Names of the parts  
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns  
sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special  
maintenance department or after-sale service department of our company. Do not repair it by yourself.  
Water-absorption  
gasket  
Water inlet valve  
Top lid  
Inner cover  
components  
Control  
panel seat  
Phenomena  
The reason  
How to settle  
Hang up to suitable height . Open and close the  
top lid once.  
The drainage cannot work, or is too slow.  
The digitron displays E1.  
Is the drain hose hang up to suitable  
height?  
Is the drain hose blocked?  
Lint filter  
Inner tub  
Clean the foreign material. Open and close  
The top Lid Once.  
Handle  
Hook  
Out tub  
cover  
Pulsator  
It stops running in midway. The digitron  
displays E2.  
Close the top lid.  
The top lid is not closed.  
Control  
panelfilm  
Power  
cord  
Are the laundries put slantingly?  
Is the machine slanting?  
Reorder the laundries. Close the top lid.  
The machine will start running after 10  
seconds of being placed horizontally.  
The safety switch acts, and the  
spinning cannot work. The  
digitron displays E3.  
Cabinet  
Drain  
hose  
Back  
cover  
Open the water tap. Open and close  
the top lid once.  
Clean the water inlet valve then open  
and close the top lid once.  
Open and close the top lid once.  
Hang up to suitable height .  
Is the water tap opened, or is there water  
supply failure?  
Is the water inlet valve blocked?  
Is the water pressure too low?  
Is the drain hose hang up to suitable  
height?  
The water filling does not work, or is  
slow, the digital displays E4.  
Base  
Fixed foot(3 pcs)  
Adjustable foot  
Adjustable foot  
film  
Please contract the after-sales  
service department  
The water level sensor is bad.  
The digitron displays F1.  
Not wash  
Is there power failure?  
Is the power plug inserted tightly?  
Is the water level reached preset position?  
Please use it when there's power supply.  
Insert the power plug tightly.  
Fill water to the preset position.  
The machine does  
not act  
Insert the power plug tightly.  
Close the top lid.  
Set the laundries flat.  
Is the power plug inserted tightly?  
Is the top lid closed reliably?  
Are the laundries set flat?  
Not spin  
Meaning and description of the symbols  
Is the machine slanting?  
Are the laundries put slantingly in spinning?  
Are there any foreign materials?  
Adjust the machine to be even  
Reorder the laundries and close the top lid.  
Remove the foreign materials.  
There's abnormal sound  
inside the machine  
Is the jointer of water  
inlet hose loose or awry?  
The water tap leaks  
Warning sign  
Fasten the jointer properly.  
Contents marked with that symbol are related to the  
safety of the product and the personal safety of the users.  
Please operate in strict conformity to the contents.  
Common phenomena  
Phenomena  
Explanation  
Balance the laundries to avoid slanting.  
The spinning is intermittent when it starts.  
Select spin program, but it does not work.  
The program is setting the drain time , certain  
period is needed before it starts spinning.  
Contents marked with that symbol are actions forbidden  
to perform. Performing of those action may result in  
damage of the machine or influence the personal safety of  
the users.  
Forbidden sign  
The pulsator pausesduring water  
inlet in washand rinse.  
It is toavoid splashing duringwater inlet  
There may be some water flowing out of the  
drain hose in the first use of the machine.  
It is the water remained performance inspection  
by the factory.  
16  
1
 
Safety precautions  
Disposal after washing  
After using, please clean the lint and foreign materials of the lint filter etc. in time. Otherwise it may influence  
your using the machine.  
Please first pull off the power plug from the receptacle before cleaning.  
Please insert the power cord into special rece- The power cord plug should be convenient  
ptacle with rated voltage.If the power cord is to be pluged in or pluged out with hand  
three-phase wire,please use three-phase rec- while the washing machine runs normally.  
eptacle.The earthing terminal of the receptacle Be sure to pull the plug out and close the  
must be earthed reliably.If it is two-phase wire, water tap when the machine is idle,when  
please guarantee that the earthing wire is ear- moving the machine,or when cleaning  
thed reliably.If possible ,please adopt electric the machine.Do not use wet hand to ins-  
The lint filter must be used during washing.  
It must be cleaned in time after each using.  
Up  
leakage protector.  
ert or pull out the power plug.  
Install  
Lint filter:  
1.Push down the spring piece of the top lint filter to  
Dismantle  
make the claws out of the filter cover, and then  
Down  
pull out the lint filter to get it down. figure1  
2.Pull the back of the lint filter, and then you can get  
Figure 1  
Do not damage the power cord,bend ,extend,twist,bind or alter it by force.Do not press or  
nip it with weight.If the power cord or the power plug is bad, or the power plug becomes  
flexible,to avoid risk it is required to have it replaced by the technicians of our special  
shop or the costomer care agent. Keep the pin of the power plug clean,if the  
power plug is polluted with dust,please wipe with dry cloth carefully.  
down it off the front cover of the lint filter. figure2  
3.Sweep the rubbish in the lint filter.  
4.Put the back of the lint filter into the front cover .  
Up  
The back cover of lint filter  
Dismantle  
5.Put the lint filter into filter cover, and make it tight .  
Install  
6.Make sure the lint filter well installed, or it can  
influence your use.  
Down  
The front cover of lint filter  
Figure 2  
Do not put the machine at damp place like  
Do not use water hotter above 50 C .  
the bathroom. Never wash it with water.  
Not put wet laundries on the control panel.  
The filter screen of the water inlet valve is likely to be  
blocked by foreign materials and influence the water  
inlet.  
If the cabinet is dirty, wipe it with wet cloth  
Do not flush it directly with water.  
Wipe it with neutral detergent.  
Please clean it with brush every two months.  
Do not wipe it with thinner, petrol, alcohol etc.  
In case the washing machine is installed  
Do not wash water-proof laundries like  
on ground with carpet, do not block the  
ventilation hole with carpet.  
abnormal vibrations.  
the raincoat, bike covers etc. to avoid  
The ventilation holes  
at the bottom  
soft items  
1.After washing, close the water faucet. ( If needed, you can dismantle the water inlet hose).  
2.Do not store water in the washing machine for a long period. Drain the water completely after each using.  
3.Be sure to pull off the power plug before maintenance.  
Do not let the machine share one receptacle  
with other electric appliances. If the power  
plug is damaged, or the plugging into the  
receptacle is loose, do not use the plug any  
more.  
4.Hang up the power cord and drain hose.  
5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid for some time (  
about 1 hour), then close the top lid.  
2
15  
 
Safety precautions  
Do not stretch hands into the working  
machine. It is dangerous even if the  
rotation is slow. Take special care of  
the children.Do not let the children  
climb the washing machine.  
Do not decompose, repair or alter the  
machine by yourself.  
Water Level and Time Table for Each Program (self programming not included)  
Water  
level  
Rinse(minutes)  
Total time(minutes)  
About 43  
Wash(minutes)  
About 18  
Spin(minutes)  
About 4  
Program  
Rinse twice, about 17  
STANDARD  
Save  
1~4  
Saving water program, total about 10 minutes  
Rinse twice, about 17  
1
About 10  
About 31  
About 4  
About 4  
About 6  
GENTLE  
1~4  
SOAK+WASH  
about 40  
About 65  
Rinse twice, about 17  
HEAVY  
1~4  
Do not put any hot or heavy items (such  
as the kettle with hot water ) on the  
washing machine.  
Do not wash laundries with volatile  
materials (such as thinner, petrol etc.)  
Totaltime will add3  
9 minutes duringDISINFECT selected  
l
tro  
r
e
Pe  
inn  
h
T
Attention:  
Total time: including the normal water inlet time and drain time.  
Spin time: the time from intermittent running to finishing  
When selecting SAVE wash program, wash, rinse and spin are set  
automatically.  
*
*
*
The handicapped or children without  
care shall not use the machine.  
Keep the machine away from direct  
sunlight and heat source like the heater.  
5 Push START/PAUSE button  
START  
PAUSE  
5 Close the top lid  
If you open the top lid, the machine will stop  
working except for water filling and draining  
To prevent your laundries and washing  
machine from damage,be sure to take  
out all of the foreign materials from your  
pocket,such as coins,buttons,sand or  
hair pins etc.  
Please keep the lint filter in good condition,  
and install it to proper position. If the lint  
filter is lost or damaged, please contact  
costomer care agent of our company.  
6 Washing finished  
Install  
Before washing,please check if the water  
tap is open ,and if the water inlet pipe is  
connected properly.  
Dismantle  
The power will be switched off automatically  
after the finishing of the washing.  
It is suggested to use low-foaming was-  
hing powder  
After the finishing of  
the washing,It will  
give an alarm  
3
14  
 
Installation and adjustment  
Please install and adjust the machine according to the requirement of the manual. It is  
very important to your security and correct operating the machine.  
After switching on the power, the washing machine will set to common program including"wash, rinse,  
spin "automatically.To select other procedures, push the " WASH"," RINSE"or "SPIN"button to select the  
time of wash and spin, and the times of rinse. After switching on the power,if you push one of the  
button among "RINSE"and"SPIN the digitron of the former procedures will turn off automatically. The  
former procedures will not run. For instance: after switchingon the power. If you push the "SPIN" button  
first, it will execute spin singly after starting.  
Install the inner cover  
1.Open the top lid of the washing machine.  
2.Put the inner cover component on the outer tub cover, aiming the inner cover  
shaft to the installation hole of the corresponding outer tub cover shaft groove.  
3.Firstly insert the inner cover shaft of one side into the corresponding outer tub  
cover shaft groove, then push the another inner cover shaft into the corresponding outer  
tub cover shaft groove. Please install to designated position to guarantee there are no  
dropping or abnormal sound in opening and closing of the inner cover, and the operation  
shall be smooth. Do not dismount the inner cover component after washing.  
Outer tub cover  
Attention  
Even there's no water in the tub, a certain period is  
required before spin starting.  
Separate the laundries that are not colorfast from  
other laundries in washing.  
Right hand  
Outer tub cover shaft groove  
Do not use the HEAVY program for the woollen textiles.  
The pulsator will not rotate unless the water is  
filled to water level .  
Inner cover shaft  
Left hand  
Inner cover component  
After the machine starts operation, you can set the program and procedure during washing,  
set spinning time during rinsing but can not make setting in other cases.  
Figure 2  
Figure 1  
Install the bottom plate  
Back  
Front  
After you open the package, please lean the washing  
machine gently down on softitems ( like the towel cloth,  
blanket, etc. ). Install the bottom plate to the bottom of  
the machine with the eight screws by a cross screwdriver,  
then lift the machine up gently. See to the figure:  
Press " WATER LEVEL "button,  
select suitable water level  
WATER LEVEL  
Bottom plate  
Screw soft items  
After switching on the power, select a suitable water level to detect the cloth. To select other water level.Refer  
to "water level, water quantity and desoge of powder"in Page 9 and "WATER LEVEL/DISINFECT"button in Page  
10 for the selection.  
Adjust the installation position  
The washing machine shall be more than 20mm away from the wall.The largest allowed  
slope of the supporting base of the machine is 2 . The slanting or rough ground will  
result in unstable running or stoppage of the machine. Please adjust it with following  
methods:  
Page 10  
Page 9  
Confirm it's horizontal:  
Hang the lead line to confirm if it is horizontal.  
Adjust the adjustable foot:  
1.To twist the adjustable foot, please first  
lift up the side of the foot slightly, loosen  
the adjustable nut, and twist the foot.  
2.Fasten the nut after adjustment.  
adjustable nut  
Loosen  
Fasten  
adjustable foot  
High  
Low  
4
13  
 
How to change the direction of the drain hose  
Steps of using the operation buttons  
and description of the steps  
b
1.Lean the machine down gently with the front  
surface facing the ground. Loosen the eight  
screws by a cross screwdriver.  
3.Extend the drain hose from the left side. Push the  
drain hose into the groove with hands.  
Bottom plate  
Back  
Push the drain hose  
into the groove with  
Front  
POWER  
ON/OFF  
Soft item  
START  
PAUSE  
MIN  
2.Pull out the drain hose from the groove at the  
right side.  
4.Install the bottom plate (as per indicated before),  
then lift the machine up gently.  
Use groove at  
this side after  
direction changing  
1 Push the POWER ON/OFF button to  
switch on the power  
POWER  
ON/OFF  
After switching onthe power,DISINFECTis not selected  
To select DISINFECT,push WATERLEVEL/DISINFECT over 2 seconds,  
the DISINFECT function works,then push2 or 3 to select asuitable program.  
Using the drain hose  
2 Push the PROGRAM SELECTION button to  
select the suitable automatic program  
PROGRAM  
The drainage shall be smooth with the drain hose.  
1.put the drain hose up to suitable position (Do not  
put it on ground.)  
Notes: The highest point of drain pipe shuold be  
higher than the water level of washing tub for  
avoiding to siphon phenomenon during drain.  
After switching on the power, the machine will set to STANDARD program automatically. To select other  
program, push the PROGRAM SELECTION button till the corresponding indicator is on. Refer to the  
PROGRAM SELECTION button in Page 11.  
2.Do not step on or press the drain hose.  
For example: select SAVEwashfor the quick washing of  
the laundries with light dirt.  
Page11  
3 Push WASH RINSE SPIN button to select  
suitable programs  
0.7m<H<1.2m  
MIN  
12  
5
 
Install the water inlet hose  
Power On/Off button  
button to switch on  
s on, push it again  
Push the POWER ON/OFF  
the power. When the power i  
to switch off the power.  
Wash remain time indicator digitron  
The program is selectedbut not on,It displays the total minutes  
of the program  
button to switch on  
Push the POWER ON/OFF  
the power. If the START/PAU  
pushed, the washing machine  
switch off the power after 5 m  
During operation of programs, it displays the remained time (minute).  
SE button is not  
will automatically  
inutes.  
In case of abnormal phenomenon, it displays the abnormal symbol (see to Page 16)  
1. Attach the water inlet hoses to the water faucet. Using pliers, tighten  
the coupling. ( As figure 1)  
Page 16  
NOTE: Do not over tighten. Damage to the  
valves can result.  
Start/Pause  
After the power is switched on, push it to  
button  
Start the machine  
During working, push it to pause working.  
During pause, push it to resume working.  
2. Connect the other ends to the water inlet valve .  
( As figure 2)  
Figure 1  
Jointer of the water inlet hose  
POWER  
ON/OFF  
Jointer of the  
water inlet valve  
START  
PAUSE  
Figure 2  
Water absorption cushion  
WASH button  
PROGRAM SELECTION button  
Push the WASH buttonto set the wash  
procedure.  
You can select from the following four programs.  
During STANDARD GENTLE HEAVY  
programs, push theWASH button to set  
different wash time (STANDARD from0 to  
25minutes GENTLE from 0 to 15  
minutes;HEAVY from 30 to 50 minutes or 0  
minutes )  
Normal wash  
STANDARD  
HEAVY  
Large, thick or heavily soiled laundry  
Woollen textiles or underwear  
GENTLE  
SAVE  
10 min quick wash for load below 2 kg  
During SAVE program, push the WASH  
button, the machine have no reaction.  
6
11  
 
4 Use the operation buttons  
A.  
Description of the function of the buttons  
Check the connection between the water inlet  
hose and the water tap  
Mode and meaning of the indicator light  
Digital tube  
Off  
During operation of programs, it displays the  
remained time (minute) or remained times of  
the corresponding procedure  
1.Swaying the hose gently to confirm if it is fastened  
stable.  
Flashing: indicate the runningprogram  
On: indicate the programabout to run, orindicate the selected mode  
2.After installation, open the tap to check if it leaks.  
3.Do not bend the hose with overstrain.  
4.Before each usage please check if the connection  
between the water inlet hose and the water tap, is firm,  
so as to prevent dropping from improve Installation  
position.  
Take down the water inlet hose  
1.Close the water tap.  
2. Pull off the water inlet hose from the water tap and washer  
MIN  
Push WATER LEVEL/DISINFECT button to select a  
suitable water level.  
After the machine is started, You shall push the START/  
-PAUSE button and then push WATER LEVEL/DISINF  
-ECT button make new setting.  
During SAVE program,WATER LEVEL/DISINFECT  
will not be changed.  
button  
RINSE  
utton  
N b  
SPI  
During operation of wash and rinse program, you can  
push down the water level button to add water. When you  
release the button, or it reaches the overflow water level,  
Push the RINSE button to set  
Push the SPIN button to set  
the spin procedure.  
the rinse procedure.  
During STANDARD GENTLE  
HEAVY programs,push the RINSE  
button to set different rinse times  
During STANDARD GENTLE  
HEAVY programs,push the  
spin button to set different spin  
the machine will stop adding water .  
Push WATER LEVEL/DISINFECT over 2  
seconds , DISINFECT tube is light;Push  
WATER LEVEL/DISINFECT over 2 seconds again,  
DISINFECT tube is off and the DISINFECT function  
is canceled.During the washing maching working,  
push START/PAUSE button ,you can make  
new selected.  
(
0, 1, 2, 3, 4 times)  
minutes  
(
0
9 minites)  
During SAVE program,push  
the rinse button,the machine have  
no reaction  
During SAVE program,push  
the spin button,the machine have  
no reaction  
10  
7
 
1 Preparation before washing  
3 Add the detergent  
Preparation before washing  
1.Connect the water inlet hose and open the water tap .  
2.Confirm that the washing machine isearthed reliably . The  
insert the powerplug into the receptacle. Do not connect the  
earth terminal to the gas pipe and tap water pipe.  
3.Put up the drain hose.  
How to use the washing  
powder  
Direct dissolved in the machine  
1.Fill water to "1" level.  
0.7m<H<1.2m  
2.Add the power. Run for 30 seconds to  
dissolve it completely.  
3.Put in the laundries. Select suitable water level.  
The instant dissolving of the washing powder:  
1.Prepare warm water of 30 C and a container.  
2.Add the powder while stirring to fully  
dissolve it.  
The powder is more prone to pollute the  
laundries than the detergent. Therefore  
please use it with proper quantity.  
Washing powder with poor quality or not used  
for a long period may get blocked. Please  
clean the detergent box in time.  
4.Slanting or uneven ground may result in unstable working  
or abnormal noise. Please make the machine stand horizontally.  
How to usethe whitener  
Pay attention to followings before washing the laundries  
Fill water to decided level. Dilute the whitener  
with container. Pour it slowly into the washing  
tub.  
Avoid using whitener on laundries with color  
or pattern as they are prone to lose color.  
The whitener shall not touch the laundries  
directly.  
Refer to the user's manual for the usage and  
quantity of the whitener.  
For powder whitener, please dissolve it before  
use.  
Clear the pocket.  
Confirm  
if  
When the pulsator is running,  
the buttons of the laundries  
may cause noise. For the  
sake of discretion,please  
put the laundries with buttons  
into other laundries.  
Fasten the  
buttons and  
zippers.  
The quantity of  
the laundries  
shall not exceed  
the rated value.  
The big laundries  
like the jeans  
shall be put in  
loosely.  
Take out the  
coins , sand,  
hairpins etc.  
there's special  
requirment for  
the laundries.  
Different washing powders have different  
dosage. Please refer to the usage manual of  
the washing powder for the details.  
Standard usage quantity of the detergent and water  
quantity  
a.Please check if the laundries are applicable for washing.  
b.Separate those not colorfast from other laundries.  
Concentrated  
powder  
(Add 25g in each  
30L water)  
Common powder  
Laundries  
quantity(kg)  
Water level  
Water quantity  
c.For laundries not waterabsorbing,please put them into water with hands.  
d.For laundries with much soil,please remove the soil first.You can add detergent on the  
part with serious soil directly.It is much easier to remove the soil by that mean.  
e.For laundries likely to get lint ball or with long fiber,please first turn the inside out before  
putting them into the water.  
(Add 40g in each  
30L water)  
About 32L  
About 26L  
About 42.7g  
About 34.7g  
About 26.7g  
About 21.7g  
4
3
1.5~3.3  
1.5  
f.Do not put the laundries polluted with chemicals directly into the washing machine.  
About 21L  
About 17L  
About 28g  
About 21.3g  
About 17.5g  
About 13.3g  
2
1
2 Put in the laundries  
The capacity of washing and spinning of the machine refer to the largest weight  
of the standard laundries under dry condition that can be washed or spun in  
one time. One time washing quantity shall be lower than the rated capacity.  
The thicknesses, size, type of the cloth will influence the actual washing capacity.  
It is suitable for one time washing to put in reasonable amount of laundries and  
the laundries can be turned round in washing.  
Do not select 4 water level for laundries smaller than 0.8kg, so as to avoid  
splashing of water.  
9
8
 

Graco Stroller 1757083 User Manual
Haier Saw HRF 418W User Manual
Hans Grohe Indoor Furnishings 35115801 User Manual
Harbor Freight Tools Air Compressor 90385 User Manual
Honeywell Network Card UDC 6300 User Manual
Hotpoint Range RB787WC BC User Manual
Hotpoint Refrigerator 8350 User Manual
HP Hewlett Packard Computer Drive 5000I User Manual
Igloo Refrigerator fr465 User Manual
IMC Networks Computer Hardware MCPC 10 100 User Manual