Haier Saw 1407 User Manual

COLOR TV RECEIVER  
OWNER'S MANUAL  
The Owner`s Manual for the Follow Models:  
21F9D-P, 21T9D-P,21F9D,21T9D,1407  
Please READ this manual carefully  
before operating the unit, and keep  
it for future reference.  
 
Warning and cautions  
1. When you clean the TV set, please 4. Do not place the TV set near rain or  
pull out the power plug from AC outlet.  
Don't clean the cabinet and the  
screen with benzene, petrol and other  
chemicals.  
moisture as it may cause an electric  
shock, or the TV set to catch fire. The  
TVsetmustonly  
beusedindryin  
door locations.  
2. In order to prolong the using life of  
the TV set, please place it in a well  
ventilatedlocation.  
5. The back cover must only be  
removed by a registered electrical  
service person. Removing the back  
cover may result in electric shock, fire  
or damage to  
the TV set.  
6. If the TV set is not going to be used  
for a long time, or there is a severe  
thunder & Lighting storm, it is  
recommended that the TV set be  
disconnected from the AC power outlet  
and the aerial plug removed.  
3. Don't place the TV  
set in direct sunlight  
ornearaheatsource.  
Explanation on the display tube  
In general, it is not needed to clean the tube surface. However, necessary,  
it's surface can be cleaned with a dry cotton cloth after cutting off the power.  
Don't use any cleanser. If using hard cloth, the tube surface will be damaged.  
 
Installation  
Aerial connection  
Generally speaking, to enjoy a clearer picture, we recommend that you use a CATV  
system or an outdoor antenna .In different places, the suitable antenna type and position  
are different.  
300 twin-lead cable  
Antenna adapter  
(additional purchase)  
Mixer  
additional  
purchase  
75  
coaxial cable  
Antenna input  
75 standard  
coaxial type  
Plug  
(additional purchase)  
AC power socket  
Note  
* It is recommended that you'd better use 75 coaxial cable to remove the  
disturbance caused by airwave.  
* Don't bind antenna cable and power wire together.  
Preparation of the remote control unit  
Battery installation  
Take off the battery compartment cover. Place two AAAbatteries, make sure that battery  
polarity matches with the +/- mark inside the battery compartment.  
Operation notes for the remote control unit  
Under normal conditions, the life time of batteries is one year.  
If you don't intend to use the unit for a long period or the electricity of the batteries is  
used up, remove the batteries to prevent batteries acid from leaking into the battery  
compartment.  
Don't throw your batteries into a fire. Dispose of your batteries with a specified method.  
Avoid the falling and the wetting of the remote control unit.  
 
Function buttons and external sockets  
Front and side panel of the TV set  
1407  
VIDEO R-AUDIO-L  
Power switch  
Signal receiver  
Power indicator  
Video R/L Audio  
TV/AV  
MENU  
VOL-  
VOL+  
CH-  
CH+  
Menu  
TV/AV  
switching  
Volume up/ down  
Channel position up/down  
21F9D, 21F9D-P,  
21T9D, 21T9D-P  
VIDEO  
Video Input  
terminal  
L
Audio Input  
terminal  
AUDIO  
R
Power indicator Sensor window Power switch  
MENU  
AV/TV  
(input selector  
Volume up/ down  
Channel selector  
Note: The cabinet and buttons of TV is only for reference.  
Rear panel of the TV set  
EXT  
Antenna input  
TV SCRAT Terminal  
If you want to connect the TV set to the other audio/video equipment, please  
refer to P22.  
 
Buttons on the remote control  
Buttons and Descriptions  
MUTE  
POWER  
Mute Button  
CALL  
SWAP  
Press to concealthe sound ofprograms.  
Stand by Button  
TV/AV  
-/--  
Screen Display Button  
Swap function Button  
TV andAV Exchange Button  
To exchanger betweenTV and  
other available videoinputs  
Digital selector  
1
4
2
5
8
0
3
6
7
SCAN  
9
TIME  
Program number Button  
Program scan Button  
Time menu  
P.STD  
FUNCTION  
Picture mode selection  
Function menu  
CH+  
Menu Select/Adjust Button  
Use this buttonto adjust themenu,  
the volume andthe channels.  
Tune menu  
VOL  
-
VOL  
+
MENU  
CH-  
Picture menu  
PICTURE  
TUNE  
EXIT  
Exit screen display  
 
Switching on/ off the TV set  
In the following, the methods of using power switch and remote controller to switch  
on/off power supply for the TV set will be explained.  
Switching on/ off the TV set  
Switching on/ off the TV set  
1 Please press the power switch to switch on AC  
power supply and the power indicator will light.  
2 If the indicator is lighting in red, press the POWER  
button on the remote control again.  
Note  
1 When you don't operate the TV set with a  
remote control, you can turn on it directly  
through pressing the P+/- buttons on the TV set  
(Child Lock must be turned off).  
4
AUTO  
BG  
2 If you want to exchange to standby status,  
please press down the POWER button on the  
POWER  
remote control.  
3 If you want to fully switch off the power supply  
for the TV set, please press the power switch  
button on the TV set.  
Auto switch-off function  
When the "Back" function is on, if an empty  
channel is selected or the TV programs are  
ended for the day, the power will be switched off 5  
minutes later automatically. If the "OFF TIME" is  
on, it will be switched off according to the  
presetting time. The auto power off function does  
not work under video input or when the  
background is off.  
(Note: If the "off timer" is less than 5 minutes, it  
will be switched off automatically to the preset  
Time. )  
 
Watching TV  
You can watch TV program in a preset channel.  
Watching TV program  
How to select TV program  
Select the desired program  
1 Using "Program number" buttons  
1
4
7
2
5
8
0
3
6
9
Directly enter thechannel number withthe numeric keypad  
on the remotecontrol.  
To select channel numbersfrom 10 ~99 press [-/--]button  
and enter thetwo digit channelnumber  
To select channel numbersfrom 100 ~218 press [-/--]button  
twice and enterthe 3 digitchannel number  
2 Using the CH+/- buttons  
Press the CH+ button to select a channel number in number  
increasing direction.  
Press the CH- button to select a channel number in number  
decreasing direction.  
CH+  
Select the desired sound  
VOL  
-
VOL  
+
MENU  
Press the VOL-/+ buttons on the remote or the front of the  
TV set to adjust the volume level.  
CH-  
If the colour or sound of a channel is abnormal  
The settings of the colour  
TUNE  
system or the sound system  
TUNE  
COLOUR  
SOUND  
BAND  
AUTO  
BG  
VHFL  
OFF  
0
may be wrong.  
Press the TUNE button and  
setting menu shown on the  
right will display on the screen.  
SKIP  
PROGRAM  
SEARCH  
FINE TUNE  
AUTO SEARCH  
CH+  
If picture colour is abnormal  
VOL  
-
VOL  
+
Use the CH+/- buttons to select Colour then the  
VOL-/+ buttons to select the colour system.. Press the  
EXIT button to save the setting.  
MENU  
CH-  
If the picture sound is abnormal  
Use the CH+/- buttons to select Sound then press the  
VOL-/+ buttons to select the sound system.  
 
Watching TV continued  
Swapfunctionenablesquickswaptothelastwatchedprogram.  
Auto scan function enables automatic successive scanning of all the programs in  
memorywith "OFF"skipstatus(eachchannelwilllastabout2seconds).  
Program swap and auto scan functions  
Program swap  
1 Suppose the channel number  
you used just now is 8 and the  
channel number you are using  
is 18 (as shown in the figure).  
18  
AUTO  
BG  
SWAP  
8
AUTO  
BG  
2 If you want to return to the  
last watched program channel  
8, you can simply press the  
SWAP button.  
18  
AUTO  
BG  
3 If you want to return to  
channel 18, press the button  
again. Through this function,  
you can easily change  
between the channel you are  
using and the channel you  
used last time.  
Auto program scan  
1 If you want to select a  
desirable program, you may  
scan all the TV programs in  
memory. You can simply press  
the SCAN button to do this. The  
programs will appear one after  
another from beginning to end  
(each channel number will last  
about 2 seconds).  
1
AUTO  
BG  
SCAN  
2
AUTO  
BG  
SCAN  
SCAN  
3
AUTO  
BG  
SCAN  
1
AUTO  
BG  
2 If you want to stop the function  
during auto scanning, simply  
presstheSCANbutton again.  
 
Searching channel  
This TV set has three methods to set the channels, which are respectively full  
automatic, semi automatic and manual fine tune.  
-
In this section, how to use the remote control to set the channel is explained. You  
can also use the buttons on the TV set to set channel.  
Full automatic mode  
1 Press the TUNE menu button ,  
TUNE  
till the TUNING menu shown on  
TUNE  
COLOUR  
SOUND  
BAND  
AUTO  
BG  
VHFL  
OFF  
0
the right display on the screen.  
SKIP  
PROGRAM  
SEARCH  
FINE TUNE  
AUTO SEARCH  
2 Press the CH+/- buttons to  
select "AUTO SEARCH".  
CH+  
TUNE  
COLOUR  
SOUND  
BAND  
AUTO  
BG  
VHFL  
OFF  
0
VOL  
-
VOL  
+
MENU  
SKIP  
PROGRAM  
SEARCH  
FINE TUNE  
AUTO SEARCH  
CH-  
3 Press the VOL+ button to  
ensure automatic search  
function operates. All channels  
now playing program will be  
automatically preset in order .  
After the search has finished,  
the first program number will  
display on the screen.  
Display function  
CALL  
Press the CALL button, then  
the channel number and the  
systems will be displayed on  
the screen.  
4
AUTO  
BG  
 
Searching channel  
Continued  
Semi-automatic search  
Semi-automatic search  
1 Press the CH+/- buttons or  
PROGRAM NUMBER 0-9  
buttons to choose desired  
channels I.E. channel 1  
1
AUTO  
BG  
TUNE  
2 Press the TUNE menu button ,  
till the TUNING menu shown on  
the right display on the screen.  
3 Press the CH+/- buttons to  
select " SEARCH".  
CH+  
TUNE  
COLOUR  
SOUND  
BAND  
AUTO  
BG  
VHFL  
OFF  
0
VOL  
-
VOL  
+
MENU  
SKIP  
PROGRAM  
SEARCH  
FINE TUNE  
AUTO SEARCH  
CH-  
4 Press the VOL-/+ buttons to  
1
start searching.  
The VOL- down button is used  
for lower side program search.  
The VOL+ up button is used for  
higher side program search.  
Repeat this step, till find the  
desired channel.  
To turn off the on-screen menu  
In general, after you press the MENU button, the menu item  
display (PICTURE, TIME, FUNCTION, TUNE, EXCHANGE,  
ETC.) will automatically disappear within 15 seconds. If you  
want to eliminate these contents immediately, please press  
the EXIT button.  
EXIT  
 
Searching channel  
Continued  
Manual fine tune  
Manual fine tune  
If the picture and/or sound are poor, try using the FINE  
TUNE feature. Do not use this feature unless  
reception is poor.  
CH+  
1 Press the CH+/- buttons or  
PROGRAM NUMBER 0-9  
button to choose desired  
channels I.E. channel 1  
1
AUTO  
DK  
VOL  
-
VOL  
+
MENU  
CH-  
2 Press the TUNE menu button ,  
till the TUNING menu shown on  
the right display on the screen.  
TUNE  
3 Press the CH+/- buttons to  
select " FINE TUNE".  
TUNE  
COLOUR  
SOUND  
BAND  
AUTO  
BG  
VHFL  
OFF  
0
SKIP  
PROGRAM  
SEARCH  
FINE TUNE  
AUTO SEARCH  
CH+  
VOL  
-
VOL  
+
MENU  
CH-  
4 Press the VOL-/+ buttons all  
through to carry out fine tune,  
till the best picture and sound  
are obtained.  
1
FINE TUNE  
152.25MHz  
 
Searching channel  
Continued  
Program skip  
Program skip  
The Program skip feature enables you to skip/hide  
programs that you do not wish to be displayed when  
using the CH+/- buttons. These channels will still be  
displayed by directly using the channel number  
buttons on the remote control.  
CH+  
1 Press the CH+/- buttons or  
PROGRAM NUMBER 0-9  
button to choose desired  
channels I.E. channel 1  
1
AUTO  
BG  
VOL  
-
VOL  
+
MENU  
CH-  
2 Press the TUNE menu button ,  
till the TUNING menu shown on  
the right display on the screen.  
TUNE  
TUNE  
COLOUR  
SOUND  
BAND  
AUTO  
BG  
VHFL  
OFF  
0
3 Press the CH+/- buttons to  
select "SKIP".  
SKIP  
PROGRAM  
SEARCH  
FINE TUNE  
AUTO SEARCH  
4 Press the VOL-/+ buttons to  
turn the SKIP function "ON".  
CH+  
TUNE  
COLOUR  
SOUND  
BAND  
AUTO  
BG  
VHFL  
ON  
VOL  
-
VOL  
+
MENU  
5 Press the TUNE button to close  
the menu. When you use the CH+/-  
buttons to select channel, this  
channel will be skipped. However,  
you can still use the PROGRAM  
NUMBER buttons to select the  
skipped channel numbers.  
SKIP  
PROGRAM  
SEARCH  
FINE TUNE  
AUTO SEARCH  
0
CH-  
If you want to recover the skipped channel  
1 Use the PROGRAM NUMBER buttons to select the channel  
number to be recovered.  
2 Repeat those steps just now.  
3 Press the VOL-/+ buttons to turn the SKIP function "OFF".  
 
Convenient picture and sound control functions  
Multiple picture modes  
How to select picture modes  
You can quickly select the desired picture mode from  
four preset modes and one customized mode.  
P.STD  
Press the P.STD button to select the  
STANDARD  
desired picture quality. Five kinds  
RICH  
of picture modes (i.e., "STANDARD",  
"RICH", "USER","LISTEN",  
USER  
"SOFT" ) can be selected in turn.  
LISTEN  
SOFT  
How to customize your own picture status  
1 Press the PICTURE menu button , till the PICTURE menu  
PICTURE  
shown on the right display on the screen.  
2 Press the CH+/- buttons to  
PICTURE  
select the item to adjusted,  
then press the VOL-/+ buttons  
to obtain the desired effect.  
CONTRAST  
BRIGHTNESS  
COLOUR  
SHARPNESS  
*HUE  
48  
32  
48  
40  
60  
CH+  
VOL  
-
VOL  
+
MENU  
BLACK STRETCH OFF  
CH-  
I T E M  
Press VOL-  
Press VOL+  
Strong  
Weak  
CONTRAST  
BRIGHTNESS  
COLOUR  
Bright  
Dark  
Deep  
Shallow  
Soft  
Sharp  
SHARPNESS  
*Hue  
lean to green  
lean to purple  
Note:  
The "Hue" item only appears when the colour system is NTSC.  
 
Convenient picture and sound control functions  
Continued  
Black Stretch-(Automatically Increases the Contrast Rage)  
Noise Reduce - (Picture Noise & Grain Reduction Circuit. Only use on poor reception.)  
Black stretch and noise reduce  
How to select BLACK STRETCH  
PICTURE  
1 Press the PICTURE menu  
button , till the PICTURE menu  
PICTURE  
shown on the right display on the  
CONTRAST  
BRIGHTNESS  
COLOUR  
48  
32  
48  
40  
60  
screen.  
SHARPNESS  
*HUE  
CH+  
BLACK STRETCH OFF  
2 Press the CH+/- button to  
select "BLACK STRETCH".  
VOL  
-
VOL  
+
MENU  
CH-  
PICTURE  
CONTRAST  
BRIGHTNESS  
COLOUR  
SHARPNESS  
*HUE  
48  
32  
48  
40  
60  
3 Press the VOL-/+ buttons to  
turn the BLACK STRETCH  
function "ON" or "OFF".  
BLACK STRETCH ON  
How to select NOISE REDUCE  
1 Press the FUNCTION menu  
button, till the FUNCTION menu  
FUNCTION  
shown on the right display on the  
ENGLISH  
FUNCTION  
screen.  
BACKGROUND  
NOISE REDUCE  
FADE  
CHILD LOCK  
AVL  
CALENDAR  
ON  
ON  
ON  
OFF  
ON  
CH+  
2 Press the CH+/- buttons to  
select "NOISE REDUCE".  
VOL  
-
VOL  
+
MENU  
FUNCTION  
ENGLISH  
BACKGROUND  
NOISE REDUCE  
FADE  
CHILD LOCK  
AVL  
CALENDAR  
CH-  
ON  
OFF  
ON  
OFF  
ON  
3 Press the VOL-/+ buttons to  
turn the NOISE REDUCE  
function "ON" or "OFF".  
 
Convenient picture and sound control functions  
Continued  
Mute function  
Sound mute  
1 Press the MUTE button on the  
remote control and "MUTE" type  
MUTE  
face will display on the lower part  
of the screen. At this time, the  
sound of the TV set is turned off.  
MUTE  
2 If you want to recover the sound,  
press the MUTE button again or  
directly press the VOL-/+ buttons.  
 
Time functions  
Clock setting and timer on/off functions  
Clock setting  
The clock will only work if the TV set if left turned on  
or in standby. When the set is disconnect from the  
power supply or is turned off by the main power on  
the front panel, the clock losespower and will need to  
be reset when the power is reconnected.  
TIME  
1 Press the TIME menu button,  
and the TIME menu display on  
the screen.  
CH+  
TIME  
CLOCK  
17:18  
18:00  
1
VOL  
-
VOL  
+
MENU  
2Press the CH+/- buttons select ON TIME  
"CLOCK", then press the VOL -  
/+ buttons to adjust the time in  
hour position; press again the  
CH+/- buttons to select the  
time in minute position, then  
press the VOL -/ +buttons to  
adjust the value of minutes .  
ON PROG  
OFF TIME  
SLEEP TIMER  
REMIND TIME  
REMIND PROG  
--:--  
0
--:--  
1
CH-  
On/off timer  
Using on/off timer function, the TV set can automatically  
turn on to a preset program or shut down in a preset time.  
1 Press the TIME menu button  
to call up the TIME menu on the  
screen.  
TIME  
TIME  
CLOCK  
ON TIME  
ON PROG  
OFF TIME  
SLEEP TIMER  
REMIND TIME  
REMIND PROG  
17:18  
18:00  
1
--:--  
0
2 Press the CH+/- buttons to  
select "ON TIME", then press  
the VOL -/+ buttons to set the  
value in hour position; press  
again the CH+/- buttons to  
select the minute position and  
set the value of the minute.(take  
18:00 as an example)  
--:--  
1
CH+  
VOL  
-
VOL  
+
MENU  
3 Press the CH+/- buttons to  
select "ON PROG", then press  
the VOL-/+ or program direct  
number buttons to select your  
desired channel (take 8 as an  
example).  
TIME  
CLOCK  
ON TIME  
ON PROG  
OFF TIME  
SLEEP TIMER  
REMIND TIME  
REMIND PROG  
CH-  
17:18  
18:00  
8
23:00  
0
--:--  
1
4 Repeat step 1-2 to set OFF  
TIME.(take 23:00 as an example)  
 
Time functions  
Continued  
Sleep timer and program preset  
Sleep timer  
The TV set have 18 sections  
0
option for sleep timer function  
(each section has a time  
interval of 10 minutes) (See right  
chart):  
10  
20  
TIME  
170  
180  
1 Press the TIME menu button,  
and the TIME menu display on  
the screen.  
TIME  
CLOCK  
ON TIME  
ON PROG  
OFF TIME  
CH+  
2 Press the CH +/- buttons to  
select "SLEEP TIMER".  
17:18  
18:00  
8
23:00  
120  
--:--  
1
VOL  
-
VOL  
+
MENU  
CH-  
3 Press the VOL -/+ buttons to  
SLEEP TIMER  
adjust the SLEEP TIMER level. REMIND TIME  
REMIND PROG  
REMIND PROG function  
Program remind timer, that displaysan on-screen reminder  
prompt, when aprogram on adifferent channel is due tostart.  
1 Press the TIME menu button  
to call up the TIME menu on the  
screen.  
TIME  
CLOCK  
ON TIME  
ON PROG  
OFF TIME  
SLEEP TIMER  
REMIND TIME  
REMIND PROG  
TIME  
17:18  
18:00  
8
23:00  
120  
2 Press the CH +/- buttons to  
select "REMIND TIME", then  
press the VOL -/+ buttons to  
set the value in hour position;  
press again the CH+/- buttons  
to select the minute position,  
and then set the value of the  
minute.(take 19:00 as an  
example)  
19:00  
1
CH+  
VOL  
-
VOL  
+
MENU  
3.Press the CH+/- buttons to  
select "REMIND PROG", then  
press the VOL -/+ buttons or  
the program direct number  
buttons to set the desired  
channel (take 18 as an  
TIME  
CLOCK  
ON TIME  
ON PROG  
OFF TIME  
SLEEP TIMER  
REMIND TIME  
REMIND PROG  
17:18  
18:00  
8
23:00  
120  
CH-  
19:00  
18  
example).  
NOTE: For REMIND PROG to  
operate CHILD LOCK must be  
turned off.  
 
Set up function  
Screen saver and childlock functions  
How to start screen saver function  
When the BACKGROUD function  
is ON, the screen will turn  
automatically as shown "NO  
SIGNAL" of moving .  
NO SIGNAL  
1 Press the FUNCTION menu  
FUNCTION  
button till the FUNCTION menu  
,
shown on the right display on the  
screen.  
FUNCTION  
ENGLISH  
2 Press the CH+/- buttons to  
select "BACKGROUND" and press  
the VOL-/+ buttons to turn the  
BACKGROUND function "ON" .  
BACKGROUND  
NOISE REDUCE  
CHILD LOCK  
AVL  
ON  
ON  
OFF  
ON  
CH+  
CALENDAR  
VOL  
-
VOL  
+
MENU  
CH-  
Child lock function  
Enables the TV front control buttons to be locked.  
1 Press the FUNCTION menu  
FUNCTION  
button till the FUNCTION menu  
,
shown on the right display on the  
screen.  
2 Press the CH+/- buttons to  
select "CHILD LOCK" and press  
the VOL-/+ buttons to turn  
CHILD LOCK function "ON" .  
CH+  
FUNCTION  
ENGLISH  
BACKGROUND  
NOISE REDUCE  
CHILD LOCK  
AVL  
ON  
ON  
OFF  
ON  
VOL  
-
VOL  
+
MENU  
CALENDAR  
CH-  
NOTE:  
All the control panel buttons on the front of the TV are disabled  
when CHILD LOCK is turned on. The power switch will still turn  
the TV set off.  
 
Set up function  
Continued  
AVL and calendar functions  
AVL function  
1 Press the FUNCTION menu  
FUNCTION  
button till the FUNCTION menu  
,
shown on the right display  
on the screen.  
FUNCTION  
ENGLISH  
BACKGROUND  
NOISE REDUCE  
CHILD LOCK  
AVL  
ON  
ON  
OFF  
ON  
CALENDAR  
CH+  
VOL  
-
VOL  
+
MENU  
2 Press the CH+/- button to select  
"AVL" .  
FUNCTION  
ENGLISH  
CH-  
3 Press VOL-/+ button to turn the  
BACKGROUND  
NOISE REDUCE  
CHILD LOCK  
AVL  
ON  
ON  
OFF  
ON  
AVL function "ON" or "OFF"  
.
CALENDAR  
Calendar function  
FUNCTION  
1 Press the FUNCTION menu  
button till the FUNCTION menu  
,
shown on the right display on the  
screen.  
FUNCTION  
ENGLISH  
BACKGROUND  
NOISE REDUCE  
CHILD LOCK  
AVL  
ON  
ON  
OFF  
ON  
2 Press the CH+/- button to select  
"CALENDAR" , then press the  
VOL-/+ buttons to the CALENDAR  
display on the screen.  
CALENDAR  
CH+  
VOL  
-
VOL  
+
MENU  
3 Press the VOL-/+ buttons to turn  
the YEAR/MONTH/DAY, press  
CH+/- buttons to set or adjust  
the YEAR/MONTH/DAY.  
CH-  
 
Set up function  
Continued  
Select a language  
Select a language  
FUNCTION  
1 Press FUNCTION menu  
button till FUNCTION menu  
,
shown on the right display  
on the screen.  
FUNCTION  
ENGLISH  
BACKGROUND  
NOISE REDUCE  
CHILD LOCK  
AVL  
ON  
ON  
OFF  
ON  
2 Press the CH+/- buttons to  
CH+  
CALENDAR  
select "  
" .  
VOL  
-
VOL  
+
MENU  
CH-  
3 press the VOL-/+ buttons to select  
the desired language. Then all the  
items will be displayed in the  
selected language.  
 
Position exchange functions  
Exchange  
Exchange  
This feature enables TV programs that may be on a wrong TV  
channel number to be swapped/exchanged. This feature is  
very useful when Automatic Search Tuning has been used, to  
reallocate the found programs to the correct channel numbers.  
CH+  
1 Press the MENU button till the  
,
EXCHANGE menu display on  
the screen.  
VOL  
-
VOL  
+
MENU  
EXCHANGE  
PROGRAM 1  
PROGRAM 2  
EXCHANGE  
6
2
CH-  
2 Press the VOL-/+ buttons or the  
PROGRAM NUMBER 0-9  
buttons to set PROGRAM 1 TO 6.  
3 Press the CH-/+ buttons to  
select " PROGRAM 2".  
CH+  
VOL  
-
VOL  
+
MENU  
4 Press the VOL-/+ buttons or  
the PROGRAM NUMBER 0-9  
buttons to set PROGRAM 2 TO 9.  
CH-  
EXCHANGE  
PROGRAM 1  
PROGRAM 2  
EXCHANGE  
6
9
5 Press the CH+/- buttons to  
select "EXCHANGE".  
CH+  
VOL  
-
VOL  
+
MENU  
6 Press the VOL-/+ buttons to set  
"EXCHANGE".  
CH-  
EXCHANGE  
PROGRAM 1  
PROGRAM 2  
EXCHANGE  
6
9
 
Connecting the TV set to the other video and audio equipment  
Connecting to the other video and audio equipment  
EXT  
To TV EXT  
To TV EXT  
To outside input  
To video/audio input  
DVD, VCD and other reproducing equipment  
Stereo  
 
Troubleshooting guide  
To assist in location possible faults use help guide below.  
BREAKDOWN PHENOMENON  
CHECKING  
PICTURE  
SOUND  
The aerial direction and connection  
Picture with snow  
Double or Triple Image  
Disturb  
Noise  
This is called ghosting which can be minimized  
with an outside aerial, and good quality cable  
and terminations. Altering the aerial direction  
can also minimize this effect.  
Normal  
Noise  
Electrical interference which can be caused by cars,  
motorbikes etc, Fluorescent lamps and dirty  
insulators on overhead power cables.  
1. Volume Sound mute.  
2. Only 1 speaker has no sound. Press S.STD button to  
choose USER mode, then check wether the BALANCE  
item value in SOUND menu equal to 0. Adjust the  
BALANCE item in SOUND menu as you wish in USER  
mode.  
No sound or 1  
speaker no sound  
Normal  
Ensure that the power supply is connected to the TV  
set and turned on. Also ensure that the TV set isnot  
in "Listen Mode" or that the brightness and contrast  
are not turned down.  
No sound  
No Picture  
Adjust colour control  
Adjust channel again  
Normal volume  
Normal or Weak Volume  
No colour  
Scramble  
Colour Purity faultwhich can becaused by movingthe  
TV set, placingmagnets near theTV screen orturning  
on/off house holdappliances such asvacuum cleaners  
near the TVset. Turnthe TV off with themains power  
switch for 15minutes. When thepower is turnon again  
the TV setwill automatically degaussthe picture. In  
server cases leavethe TV setturned off overnight.  
Colour Spot  
Normal volume  
Note:  
1.If the fault can not be repaired using the above guide consult with your local authorized service  
center.  
2.The TV set must only be repaired by a qualified registered service person. Never attempt to  
remove the back cover as the TV set has dangerous voltages in side that may cause a fatally or fire.  
3. The cabinet may produce the occasional "snapping sound" This is normal and caused by the  
materials in the cabinet expanding with room temperature changes.  
 
Specifications  
Colour system  
PAL, SECAM  
BG, DK, I  
1407  
14"color picture tube  
21"colour picture tube  
Picture tube  
21F9D, 21F9D-P,  
21T9D, 21T9D-P  
Sound output power  
Power requirements  
2W not distortional  
1407  
~ 110V-250V 50Hz/60Hz  
21F9D, 21F9D-P,  
21T9D, 21T9D-P  
~ 180V-250V 50Hz/60Hz  
1407  
60W  
70W  
Power consumption  
Dimension  
21F9D, 21F9D-P,  
21T9D, 21T9D-P  
342 Width x371 Depth x318 Height  
603 Width x475 Depth x430 Height  
mm  
mm  
1407  
21F9D, 21F9D-P,  
21T9D, 21T9D-P  
Remote control  
Owner's manual  
Battery(AAA)  
X1  
X1  
X2  
Accessories  
The design and specifications may be changed without notice.  
 
01  
0090506138B  
 

Grizzly Drill G1126 User Manual
Grizzly Saw Model H5698 User Manual
Haier TV DVD Combo HLC15B User Manual
Hans Grohe Plumbing Product 06802XX0 User Manual
Harbor Freight Tools Automobile Accessories 34313 User Manual
HP Hewlett Packard Yard Vacuum 08484 90019 User Manual
Husqvarna Blower 170BT User Manual
Husqvarna Tiller crt51 User Manual
Hypertec Carrying Case N17328LHY User Manual
IBM Computer Accessories SENG 3002 01 User Manual